20250421在榮品的PRO-RK3566開發板的Android13下頻繁重啟RKNPU fde40000.npu: Adding to iommu gr

20250421在榮品的PRO-RK3566開發板的Android13下頻繁重啟RKNPU fde40000.npu: Adding to iommu gr
2025/4/21 14:50


緣起:電池沒電了,導致榮品的PRO-RK3566的核心板頻繁重啟。
內核時間4s+就重啟。100%復現。
PRO-RK3566 + Android13啟動到這里 復位?
使用萬用表 測試 電池電壓5.746V。你充會電就OK了[破涕為笑]


現在地面站不能正常開機了,你們要把它弄好啊,否則沒有調試環境了。
別找我 ?之前都好好的


工程師日常的調味料,發出來僅為一笑^_


[ ? ?4.239790][ ? ?T1] rk808-rtc rk808-rtc: registered as rtc1
[ ? ?4.241099][ ? ?T1] RKNPU fde40000.npu: Adding to iommu gr??DR V1.18 f366f69a7d typ
23/07/17-15:48:58
ln
LP4/4x derate en, other dram:1x trefi
ddrconfig:7
LP4 MR14:0x4d
LPDDR4, 324MHz
BW=32 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=4096MB
tdqss: cs0 dqs0: 72ps, dqs1: -48ps, dqs2: -24ps, dqs3: -96ps,?
tdqss: cs1 dqs0: 72ps, dqs1: -48ps, dqs2: -24ps, dqs3: -96ps,?

change to: 324MHz
clk skew:0x60

change to: 528MHz
clk skew:0x58

change to: 780MHz
clk skew:0x58

change to: 1056MHz(final freq)
PHY drv:clk:38,ca:38,DQ:30,odt:60
vrefinner:16%, vrefout:29%
dram drv:40,odt:80
vref_ca:00000068
clk skew:0x2f
cs 0:
the read training result:
DQS0:0x3a, DQS1:0x3b, DQS2:0x39, DQS3:0x3b,?
min ?: 0x5 ?0x3 ?0x3 ?0x4 ?0x5 ?0x4 ?0x4 ?0x2 , 0x3 ?0x5 ?0x9 ?0x5 ?0x2 ?0x6 ?0x6 ?0x4 ,
? ? ? ?0x5 ?0x5 ?0x5 ?0x2 ?0x2 ?0x3 ?0x5 ?0x2 , 0x8 ?0x5 ?0x6 ?0x4 ?0x5 ?0x4 ?0x8 ?0x2 ,
mid ?:0x23 0x20 0x20 0x21 0x21 0x21 0x20 0x1f ,0x21 0x24 0x26 0x24 0x20 0x25 0x25 0x23 ,
? ? ? 0x23 0x22 0x23 0x20 0x21 0x21 0x23 0x20 ,0x25 0x22 0x23 0x21 0x22 0x22 0x26 0x20 ,
max ?:0x41 0x3d 0x3e 0x3e 0x3e 0x3e 0x3c 0x3d ,0x3f 0x43 0x44 0x43 0x3e 0x44 0x44 0x43 ,
? ? ? 0x42 0x40 0x42 0x3f 0x40 0x40 0x41 0x3e ,0x43 0x3f 0x40 0x3f 0x40 0x40 0x44 0x3f ,
range:0x3c 0x3a 0x3b 0x3a 0x39 0x3a 0x38 0x3b ,0x3c 0x3e 0x3b 0x3e 0x3c 0x3e 0x3e 0x3f ,
? ? ? 0x3d 0x3b 0x3d 0x3d 0x3e 0x3d 0x3c 0x3c ,0x3b 0x3a 0x3a 0x3b 0x3b 0x3c 0x3c 0x3d ,
the write training result:
DQS0:0x38, DQS1:0x29, DQS2:0x2c, DQS3:0x23,?
min ?:0x5e 0x5e 0x5e 0x5e 0x5e 0x5d 0x5c 0x5d 0x5d ,0x4d 0x50 0x52 0x50 0x4e 0x50 0x51 0x51 0x50 ,
? ? ? 0x52 0x53 0x52 0x50 0x50 0x52 0x52 0x52 0x51 ,0x4a 0x49 0x48 0x49 0x48 0x49 0x4c 0x4a 0x48 ,
mid ?:0x7a 0x79 0x79 0x79 0x79 0x79 0x77 0x78 0x78 ,0x69 0x6b 0x6e 0x6b 0x69 0x6b 0x6c 0x6c 0x6a ,
? ? ? 0x6e 0x6f 0x6e 0x6c 0x6c 0x6e 0x6d 0x6c 0x6d ,0x66 0x62 0x62 0x65 0x62 0x65 0x68 0x65 0x62 ,
max ?:0x96 0x94 0x95 0x95 0x95 0x95 0x93 0x93 0x94 ,0x86 0x86 0x8a 0x87 0x85 0x87 0x87 0x87 0x85 ,
? ? ? 0x8a 0x8b 0x8a 0x89 0x88 0x8a 0x88 0x87 0x89 ,0x82 0x7b 0x7c 0x81 0x7c 0x81 0x84 0x80 0x7d ,
range:0x38 0x36 0x37 0x37 0x37 0x38 0x37 0x36 0x37 ,0x39 0x36 0x38 0x37 0x37 0x37 0x36 0x36 0x35 ,
? ? ? 0x38 0x38 0x38 0x39 0x38 0x38 0x36 0x35 0x38 ,0x38 0x32 0x34 0x38 0x34 0x38 0x38 0x36 0x35 ,
cs 1:
the read training result:
DQS0:0x39, DQS1:0x39, DQS2:0x38, DQS3:0x39,?
min ?: 0x5 ?0x3 ?0x2 ?0x4 ?0x5 ?0x4 ?0x3 ?0x2 , 0x2 ?0x4 ?0x8 ?0x3 ?0x1 ?0x5 ?0x6 ?0x2 ,
? ? ? ?0x4 ?0x4 ?0x3 ?0x2 ?0x1 ?0x2 ?0x3 ?0x2 , 0x7 ?0x5 ?0x6 ?0x3 ?0x5 ?0x3 ?0x7 ?0x2 ,
mid ?:0x22 0x20 0x1f 0x21 0x21 0x20 0x1f 0x1f ,0x1f 0x23 0x25 0x22 0x1e 0x23 0x24 0x21 ,
? ? ? 0x21 0x21 0x21 0x20 0x1f 0x20 0x21 0x1f ,0x24 0x20 0x22 0x20 0x21 0x21 0x24 0x20 ,
max ?:0x40 0x3d 0x3d 0x3e 0x3d 0x3d 0x3c 0x3d ,0x3d 0x42 0x43 0x41 0x3c 0x42 0x42 0x41 ,
? ? ? 0x3f 0x3f 0x3f 0x3e 0x3e 0x3f 0x40 0x3c ,0x41 0x3c 0x3f 0x3d 0x3d 0x3f 0x41 0x3e ,
range:0x3b 0x3a 0x3b 0x3a 0x38 0x39 0x39 0x3b ,0x3b 0x3e 0x3b 0x3e 0x3b 0x3d 0x3c 0x3f ,
? ? ? 0x3b 0x3b 0x3c 0x3c 0x3d 0x3d 0x3d 0x3a ,0x3a 0x37 0x39 0x3a 0x38 0x3c 0x3a 0x3c ,
the write training result:
DQS0:0x38, DQS1:0x29, DQS2:0x2c, DQS3:0x23,?
min ?:0x5e 0x5e 0x5d 0x5d 0x5d 0x5c 0x5b 0x5d 0x5d ,0x4c 0x4f 0x52 0x4f 0x4d 0x50 0x50 0x50 0x50 ,
? ? ? 0x52 0x52 0x52 0x50 0x50 0x52 0x52 0x52 0x50 ,0x49 0x49 0x49 0x49 0x49 0x4a 0x4b 0x49 0x48 ,
mid ?:0x79 0x79 0x79 0x79 0x78 0x78 0x77 0x78 0x78 ,0x69 0x6a 0x6e 0x6b 0x69 0x6b 0x6b 0x6b 0x6a ,
? ? ? 0x6e 0x6e 0x6d 0x6c 0x6c 0x6e 0x6d 0x6c 0x6c ,0x65 0x62 0x64 0x64 0x63 0x65 0x67 0x64 0x64 ,
max ?:0x95 0x94 0x95 0x95 0x94 0x95 0x93 0x93 0x94 ,0x87 0x86 0x8a 0x87 0x85 0x87 0x86 0x87 0x85 ,
? ? ? 0x8a 0x8b 0x89 0x89 0x88 0x8a 0x88 0x87 0x89 ,0x82 0x7c 0x80 0x80 0x7d 0x81 0x84 0x80 0x80 ,
range:0x37 0x36 0x38 0x38 0x37 0x39 0x38 0x36 0x37 ,0x3b 0x37 0x38 0x38 0x38 0x37 0x36 0x37 0x35 ,
? ? ? 0x38 0x39 0x37 0x39 0x38 0x38 0x36 0x35 0x39 ,0x39 0x33 0x37 0x37 0x34 0x37 0x39 0x37 0x38 ,
CA Training result:
cs:0 min ?:0x4d 0x4d 0x44 0x42 0x42 0x41 0x49 ,0x4c 0x45 0x42 0x40 0x40 0x3d 0x43 ,
cs:0 mid ?:0x8d 0x8c 0x83 0x81 0x81 0x80 0x77 ,0x8b 0x85 0x80 0x7f 0x7f 0x7c 0x70 ,
cs:0 max ?:0xcd 0xcb 0xc3 0xc1 0xc0 0xc0 0xa6 ,0xca 0xc6 0xbf 0xbe 0xbe 0xbc 0x9e ,
cs:0 range:0x80 0x7e 0x7f 0x7f 0x7e 0x7f 0x5d ,0x7e 0x81 0x7d 0x7e 0x7e 0x7f 0x5b ,
cs:1 min ?:0x4d 0x4f 0x42 0x43 0x44 0x43 0x46 ,0x4b 0x49 0x42 0x40 0x40 0x3f 0x41 ,
cs:1 mid ?:0x8d 0x8d 0x82 0x82 0x84 0x81 0x78 ,0x8a 0x88 0x81 0x7f 0x7f 0x7d 0x72 ,
cs:1 max ?:0xcd 0xcc 0xc2 0xc1 0xc4 0xc0 0xab ,0xca 0xc7 0xc1 0xbe 0xbe 0xbc 0xa4 ,
cs:1 range:0x80 0x7d 0x80 0x7e 0x80 0x7d 0x65 ,0x7f 0x7e 0x7f 0x7e 0x7e 0x7d 0x63 ,
out
U-Boot SPL board init
U-Boot SPL 2017.09-gaaca6ffec1-211203 #zzz (Dec 03 2021 - 18:42:16)
unknown raw ID phN
unrecognized JEDEC id bytes: 00, 00, 00
Trying to boot from MMC2
MMC error: The cmd index is 1, ret is -110
Card did not respond to voltage select!
mmc_init: -95, time 16
spl: mmc init failed with error: -95
Trying to boot from MMC1
SPL: A/B-slot: _a, successful: 0, tries-remain: 7
Trying fit image at 0x4000 sector
## Verified-boot: 0
## Checking atf-1 0x00040000 ... sha256(0d5225a4ab...) + OK
## Checking uboot 0x00a00000 ... sha256(f7fa3caa7c...) + OK
## Checking fdt 0x00b457c0 ... sha256(036cca5880...) + OK
## Checking atf-2 0xfdcc1000 ... sha256(3e94d16e6a...) + OK
## Checking atf-3 0x0006b000 ... sha256(fde0ef262b...) + OK
## Checking atf-4 0xfdcce000 ... sha256(c9eb312bf2...) + OK
## Checking atf-5 0xfdcd0000 ... sha256(befba422b8...) + OK
## Checking atf-6 0x00069000 ... sha256(6ede7a3b44...) + OK
## Checking optee 0x08400000 ... sha256(6c92ef6a0e...) + OK
Jumping to U-Boot(0x00a00000) via ARM Trusted Firmware(0x00040000)
Total: 319.775 ms

INFO: ? ?Preloader serial: 2
NOTICE: ?BL31: v2.3():v2.3-607-gbf602aff1:cl
NOTICE: ?BL31: Built : 10:16:03, Jun ?5 2023
INFO: ? ?GICv3 without legacy support detected.
INFO: ? ?ARM GICv3 driver initialized in EL3
INFO: ? ?pmu v1 is valid 220114
INFO: ? ?dfs DDR fsp_param[0].freq_mhz= 1056MHz
INFO: ? ?dfs DDR fsp_param[1].freq_mhz= 324MHz
INFO: ? ?dfs DDR fsp_param[2].freq_mhz= 528MHz
INFO: ? ?dfs DDR fsp_param[3].freq_mhz= 780MHz
INFO: ? ?Using opteed sec cpu_context!
INFO: ? ?boot cpu mask: 0
INFO: ? ?BL31: Initializing runtime services
INFO: ? ?BL31: Initializing BL32
I/TC:?
I/TC: OP-TEE version: 3.13.0-743-gb5340fd65 #hisping.lin (gcc version 10.2.1 20201103 (GNU Toolchain for the A-profile Architecture 10.2-2020.11 (arm-10.16))) #5 Mon Aug 28 15:15:17 CST 2023 aarch64
I/TC: Primary CPU initializing
E/TC:0 0 hal_algo_version_init:296 CRYPTO_CRYPTO_VERSION_NEW no support. Skip all algo mode check.
I/TC: Primary CPU switching to normal world boot
INFO: ? ?BL31: Preparing for EL3 exit to normal world
INFO: ? ?Entry point address = 0xa00000
INFO: ? ?SPSR = 0x3c9


U-Boot 2017.09 (Feb 12 2025 - 12:06:11 +0800)

Model: Rockchip RK3568 Evaluation Board
MPIDR: 0x81000000
PreSerial: 2, raw, 0xfe660000
DRAM: ?4 GiB
Sysmem: init
Relocation Offset: ed21a000
Relocation fdt: eb9f94a8 - eb9fece8
CR: M/C/I
Using default environment

optee api revision: 2.0
dwmmc@fe2b0000: 1, dwmmc@fe2c0000: 2, sdhci@fe310000: 0
Bootdev(atags): mmc 0
MMC0: HS200, 200Mhz
PartType: EFI
DM: v1
Android 13.0, Build 2023.8, v2
boot mode: None
RESC: 'boot', blk@0x0001da70
Device is: UNLOCKED
DTB: rk-kernel.dtb
HASH(c): OK
ANDROID: fdt overlay OK
I2c0 speed: 100000Hz
PMIC: ?RK8090 (on=0x10, off=0x00)
vdd_logic init 950000 uV
vdd_gpu init 900000 uV
vdd_npu init 900000 uV
vsel-gpios- not found! Error: -2
vdd_cpu init 1000000 uV
io-domain: OK
INFO: ? ?ddr dmc_fsp already initialized in loader.
Model: pro-rk3566
MPIDR: 0x81000000
ethaddr = 92:79:bb:87:e4:55
eth1addr = 76:63:47:95:2e:52
eth2addr = 8e:3d:92:28:59:86
eth3addr = 0e:59:d9:0f:b4:1e
OCV Value:6000 ?6319 ?6466 ?6556 ?6621 ?6675 ?6722 ?6766 ?6809 ?6854 ?6903 ?6960 ?7026 ?7104 ?7195 ?7297 ?7404 ?7521 ?7641 ?7771 ?8051 ?ocvsize: 21
battery->design_cap: 5000
battery->qmax: 5100
battery->bat_res_up: 140
battery->bat_res_down: 20
reg read version:0 dts read version:0
battery = 7040
rk817_bat_rsoc_init: is_first_power_on = 0, pwroff_min = 0, pwron_voltage = 7104
now_cap: 3609, pre_cap: 3610
dsoc=72000 cap=3610 v=7032 pwron_v =7104 min=0 psoc=72000 pcap=3610
<rk817_bat_calc_linek>. meet=72792, diff=594, link=1333, calc: dsoc=72000, rsoc=72198
voltage_k = 18, voltage_b = 20
voltage_sys = 6976
voltage usb: 7032
battery: 7032
current_avg = -77
current_pwron = -60
remain_cap = 3609936
fcc = 5000
qmax = 5100
dsoc = 72000
rsoc = 72198
charge type: 0
debug info:
CAL_OFFSET = 0x8019
current_avg = -77
k = 18, b = 20
battery: 7040
voltage_sys = 6976
voltage_usb = 6976
current_avg = -77
dsoc = 72000
rsoc = 72198
remain_cap = 3609936
fcc = 5000
qmax = 5100
NO_CHARGER
Enable charge animation display
Exit charge: due to charger offline
Rockchip UBOOT DRM driver version: v1.0.1
VOP have 1 active VP
vp0 have layer nr:0[], primary plane: 0
vp1 have layer nr:6[0 2 4 1 3 5 ], primary plane: 4
vp2 have layer nr:0[], primary plane: 0
disp info 2, type:16, id:0
base2_disp_info couldn't be found, screen_info type[0] or id[0] mismatched
Using display timing dts
dsi@fe060000: ?detailed mode clock 161000 kHz, flags[a]
? ? H: 1200 1231 1251 1265
? ? V: 1920 2135 2141 2341
bus_format: 100e
VOP update mode to: 1200x1920p54, type: MIPI0 for VP1
VP1 set crtc_clock to 161000KHz
VOP VP1 enable Smart0[270x654->270x654@465x633] fmt[2] addr[0xedf2c000]
final DSI-Link bandwidth: 996 Mbps x 4
unsupport command data type: 48
failed to send on cmds: -22
CLK: (sync kernel. arm: enter 816000 KHz, init 816000 KHz, kernel 0N/A)
? apll 1104000 KHz
? dpll 528000 KHz
? gpll 1188000 KHz
? cpll 1000000 KHz
? npll 1200000 KHz
? vpll 644000 KHz
? hpll 24000 KHz
? ppll 200000 KHz
? armclk 1104000 KHz
? aclk_bus 150000 KHz
? pclk_bus 100000 KHz
? aclk_top_high 500000 KHz
? aclk_top_low 400000 KHz
? hclk_top 150000 KHz
? pclk_top 100000 KHz
? aclk_perimid 300000 KHz
? hclk_perimid 150000 KHz
? pclk_pmu 100000 KHz
Net: ? eth1: ethernet@fe010000
Hit key to stop autoboot('CTRL+C'): ?0?
ANDROID: reboot reason: "(none)"
Vboot=0, AVB images, AVB verify
read_is_device_unlocked() ops returned that device is UNLOCKED
avb_slot_verify.c:763: ERROR: vbmeta: Error verifying vbmeta image: OK_NOT_SIGNED
preloaded: distribute image from 'boot
ANDROID: Hash OK
Could not find "system" partition
Booting IMAGE kernel at 0x00280000 with fdt at 0x08300000...


Fdt Ramdisk skip relocation
## Booting Android Image at 0x0027f800 ...
Kernel: 0x00280000 - 0x0236e808 (33723 KiB)
ramdisk: ? ?0x0a200000 - 0x0a35e0ec (1401 KiB)
## Flattened Device Tree blob at 0x08300000
? ?Booting using the fdt blob at 0x08300000
? ?XIP Kernel Image from 0x00280000 to 0x00280000 ... OK
? ?kernel loaded at 0x00280000, end = 0x0236e808
? ?Using Device Tree in place at 0000000008300000, end 000000000832cf1c
vp0, plane_mask:0x0, primary-id:0, curser-id:-1
vp1, plane_mask:0x3f, primary-id:4, curser-id:-1
vp2, plane_mask:0x0, primary-id:0, curser-id:-1
## reserved-memory:
? drm-logo@00000000: addr=edf00000 size=187000
? drm-cubic-lut@00000000: addr=eff00000 size=8000
? linux,cma: addr=10000000 size=800000
? ramoops@110000: addr=110000 size=f0000
? vendor-storage-rm@00000000: addr=ebd15000 size=10000
Adding bank: 0x00200000 - 0x08400000 (size: 0x08200000)
Adding bank: 0x09400000 - 0xf0000000 (size: 0xe6c00000)
Adding bank: 0x1f0000000 - 0x200000000 (size: 0x10000000)
== DO RELOCATE == Kernel from 0x00280000 to 0x00200000
Total: 1671.252/1800.73 ms

Starting kernel ...

[ ? ?1.808390][ ? ?T0] Booting Linux on physical CPU 0x0000000000 [0x412fd050]
[ ? ?1.808415][ ? ?T0] Linux version 5.10.157+ (rootroot@rootroot-X99-Turbo) (Android (8490178, based on r450784d) clang version 14.0.6 (https://android.googlesource.com/toolchain/llvm-project 4c603efb0cca074e9238af8b4106c30add4418f6), LLD 14.0.6) #41 SMP PREEMPT Wed Feb 12 12:09:49 CST 2025
[ ? ?1.815954][ ? ?T0] Machine model: pro-rk3566
[ ? ?1.849153][ ? ?T0] earlycon: uart8250 at MMIO32 0x00000000fe660000 (options '')
[ ? ?1.897714][ ? ?T0] printk: bootconsole [uart8250] enabled
[ ? ?1.905955][ ? ?T0] Reserved memory: created CMA memory pool at 0x0000000010000000, size 8 MiB
[ ? ?1.915403][ ? ?T0] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[ ? ?1.982445][ ? ?T0] Zone ranges:
[ ? ?1.985998][ ? ?T0] ? DMA32 ? ?[mem 0x0000000000200000-0x00000000ffffffff]
[ ? ?1.993543][ ? ?T0] ? Normal ? [mem 0x0000000100000000-0x00000001ffffffff]
[ ? ?2.001083][ ? ?T0] Movable zone start for each node
[ ? ?2.006523][ ? ?T0] Early memory node ranges
[ ? ?2.011201][ ? ?T0] ? node ? 0: [mem 0x0000000000200000-0x00000000083fffff]
[ ? ?2.018835][ ? ?T0] ? node ? 0: [mem 0x0000000009400000-0x00000000efffffff]
[ ? ?2.026469][ ? ?T0] ? node ? 0: [mem 0x00000001f0000000-0x00000001ffffffff]
[ ? ?2.034103][ ? ?T0] Initmem setup node 0 [mem 0x0000000000200000-0x00000001ffffffff]
[ ? ?2.062097][ ? ?T0] psci: probing for conduit method from DT.
[ ? ?2.068412][ ? ?T0] psci: PSCIv1.1 detected in firmware.
[ ? ?2.074236][ ? ?T0] psci: Using standard PSCI v0.2 function IDs
[ ? ?2.080729][ ? ?T0] psci: Trusted OS migration not required
[ ? ?2.086841][ ? ?T0] psci: SMC Calling Convention v1.2
[ ? ?2.092761][ ? ?T0] percpu: Embedded 32 pages/cpu s91800 r8192 d31080 u131072
[ ? ?2.100705][ ? ?T0] Detected VIPT I-cache on CPU0
[ ? ?2.105893][ ? ?T0] CPU features: detected: GIC system register CPU interface
[ ? ?2.113718][ ? ?T0] CPU features: detected: Virtualization Host Extensions
[ ? ?2.121263][ ? ?T0] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[ ? ?2.129678][ ? ?T0] alternatives: patching kernel code
[ ? ?2.137557][ ? ?T0] Built 1 zonelists, mobility grouping on. ?Total pages: 1027656
[ ? ?2.145869][ ? ?T0] Kernel command line: storagemedia=emmc androidboot.storagemedia=emmc androidboot.mode=normal ?androidboot.dtb_idx=0 androidboot.dtbo_idx=0 ?androidboot.verifiedbootstate=orange androidboot.serialno=b5cc453fd2c776d8 console=ttyFIQ0 firmware_class.path=/vendor/etc/firmware init=/init rootwait ro loop.max_part=7 androidboot.console=ttyFIQ0 androidboot.wificountrycode=CN androidboot.hardware=rk30board androidboot.boot_devices=fe310000.sdhci,fe330000.nandc,fe2b0000.dwmmc androidboot.selinux=permissive buildvariant=userdebug earlycon=uart8250,mmio32,0xfe660000
[ ? ?2.203094][ ? ?T0] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[ ? ?2.213027][ ? ?T0] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[ ? ?2.222409][ ? ?T0] mem auto-init: stack:all(zero), heap alloc:off, heap free:off
[ ? ?2.262361][ ? ?T0] software IO TLB: mapped [mem 0x00000000e7d15000-0x00000000ebd15000] (64MB)
[ ? ?2.323582][ ? ?T0] Memory: 3980444K/4175872K available (19774K kernel code, 4218K rwdata, 8360K rodata, 1344K init, 2185K bss, 187236K reserved, 8192K cma-reserved)
[ ? ?2.339906][ ? ?T0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ ? ?2.348106][ ? ?T0] rcu: Preemptible hierarchical RCU implementation.
[ ? ?2.355174][ ? ?T0] rcu: ?? ?RCU event tracing is enabled.
[ ? ?2.360901][ ? ?T0] rcu: ?? ?RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[ ? ?2.368822][ ? ?T0] ?? ?Trampoline variant of Tasks RCU enabled.
[ ? ?2.375119][ ? ?T0] ?? ?Tracing variant of Tasks RCU enabled.
[ ? ?2.381133][ ? ?T0] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies.
[ ? ?2.390195][ ? ?T0] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[ ? ?2.402349][ ? ?T0] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ ? ?2.410811][ ? ?T0] GICv3: GIC: Using split EOI/Deactivate mode
[ ? ?2.417317][ ? ?T0] GICv3: 320 SPIs implemented
[ ? ?2.422282][ ? ?T0] GICv3: 0 Extended SPIs implemented
[ ? ?2.427946][ ? ?T0] GICv3: Distributor has no Range Selector support
[ ? ?2.434918][ ? ?T0] GICv3: 16 PPIs implemented
[ ? ?2.439822][ ? ?T0] GICv3: CPU0: found redistributor 0 region 0:0x00000000fd460000
[ ? ?2.448242][ ? ?T0] ITS [mem 0xfd440000-0xfd45ffff]
[ ? ?2.453659][ ? ?T0] ITS@0x00000000fd440000: allocated 8192 Devices @2810000 (indirect, esz 8, psz 64K, shr 0)
[ ? ?2.464568][ ? ?T0] ITS@0x00000000fd440000: allocated 32768 Interrupt Collections @2820000 (flat, esz 2, psz 64K, shr 0)
[ ? ?2.476496][ ? ?T0] ITS: using cache flushing for cmd queue
[ ? ?2.482991][ ? ?T0] GICv3: using LPI property table @0x0000000002830000
[ ? ?2.490358][ ? ?T0] GIC: using cache flushing for LPI property table
[ ? ?2.497330][ ? ?T0] GICv3: CPU0: using allocated LPI pending table @0x0000000002840000
[ ? ?2.506134][ ? ?T0] kfence: initialized - using 524288 bytes for 63 objects at 0x(____ptrval____)-0x(____ptrval____)
[ ? ?2.548855][ ? ?T0] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[ ? ?2.556317][ ? ?T0] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ ? ?2.568914][ ? ?T0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ ? ?2.579544][ ? ?T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000)
[ ? ?2.591594][ ? ?T0] pid_max: default: 32768 minimum: 301
[ ? ?2.597506][ ? ?T0] LSM: Security Framework initializing
[ ? ?2.603374][ ? ?T0] SELinux: ?Initializing.
[ ? ?2.608047][ ? ?T0] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ ? ?2.616947][ ? ?T0] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ ? ?2.628412][ ? ?T1] rcu: Hierarchical SRCU implementation.
[ ? ?2.634833][ ? ?T1] Platform MSI: interrupt-controller@fd440000 domain created
[ ? ?2.643217][ ? ?T1] PCI/MSI: /interrupt-controller@fd400000/interrupt-controller@fd440000 domain created
[ ? ?2.654683][ ? ?T1] smp: Bringing up secondary CPUs ...
I/TC: Secondary CPU 1 initializing
I/TC: Secondary CPU 1 switching to normal world boot
I/TC: Secondary CPU 2 initializing
I/TC: Secondary CPU 2 switching to normal world boot
I/TC: Secondary CPU 3 initializing
I/TC: Secondary CPU 3 switching to normal world boot
[ ? ?2.668918][ ? ?T0] Detected VIPT I-cache on CPU1
[ ? ?2.668949][ ? ?T0] GICv3: CPU1: found redistributor 100 region 0:0x00000000fd480000
[ ? ?2.668969][ ? ?T0] GICv3: CPU1: using allocated LPI pending table @0x0000000002850000
[ ? ?2.669019][ ? ?T0] CPU1: Booted secondary processor 0x0000000100 [0x412fd050]
[ ? ?2.677528][ ? ?T0] Detected VIPT I-cache on CPU2
[ ? ?2.677550][ ? ?T0] GICv3: CPU2: found redistributor 200 region 0:0x00000000fd4a0000
[ ? ?2.677566][ ? ?T0] GICv3: CPU2: using allocated LPI pending table @0x0000000002860000
[ ? ?2.677602][ ? ?T0] CPU2: Booted secondary processor 0x0000000200 [0x412fd050]
[ ? ?2.686092][ ? ?T0] Detected VIPT I-cache on CPU3
[ ? ?2.686114][ ? ?T0] GICv3: CPU3: found redistributor 300 region 0:0x00000000fd4c0000
[ ? ?2.686129][ ? ?T0] GICv3: CPU3: using allocated LPI pending table @0x0000000002870000
[ ? ?2.686164][ ? ?T0] CPU3: Booted secondary processor 0x0000000300 [0x412fd050]
[ ? ?2.686274][ ? ?T1] smp: Brought up 1 node, 4 CPUs
[ ? ?2.782363][ ? ?T1] SMP: Total of 4 processors activated.
[ ? ?2.788295][ ? ?T1] CPU features: detected: Privileged Access Never
[ ? ?2.795176][ ? ?T1] CPU features: detected: LSE atomic instructions
[ ? ?2.802081][ ? ?T1] CPU features: detected: User Access Override
[ ? ?2.808682][ ? ?T1] CPU features: detected: 32-bit EL0 Support
[ ? ?2.815086][ ? ?T1] CPU features: detected: Common not Private translations
[ ? ?2.822730][ ? ?T1] CPU features: detected: RAS Extension Support
[ ? ?2.829418][ ? ?T1] CPU features: detected: Data cache clean to the PoU not required for I/D coherence
[ ? ?2.839635][ ? ?T1] CPU features: detected: CRC32 instructions
[ ? ?2.846037][ ? ?T1] CPU features: detected: Speculative Store Bypassing Safe (SSBS)
[ ? ?2.854442][ ? ?T1] CPU features: detected: RCpc load-acquire (LDAPR)
[ ? ?2.891646][ ? ?T1] CPU: All CPU(s) started at EL2
[ ? ?2.898645][ ? ?T1] devtmpfs: initialized
[ ? ?2.926016][ ? ?T7] Trying to unpack rootfs image as initramfs...
[ ? ?2.932719][ ? ?T1] Registered cp15_barrier emulation handler
[ ? ?2.932731][ ? ?T1] Registered setend emulation handler
[ ? ?2.932739][ ? ?T1] KASLR disabled due to lack of seed
[ ? ?2.950707][ ? ?T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[ ? ?2.962226][ ? ?T1] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ ? ?2.970922][ ? ?T1] pinctrl core: initialized pinctrl subsystem
[ ? ?2.978687][ ? ?T1] NET: Registered protocol family 16
[ ? ?2.979534][ ? ?T7] Freeing initrd memory: 1400K
[ ? ?2.990902][ ? ?T1] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations
[ ? ?2.999577][ ? ?T1] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ ? ?3.009131][ ? ?T1] audit: initializing netlink subsys (disabled)
[ ? ?3.016027][ ? T37] audit: type=2000 audit(0.239:1): state=initialized audit_enabled=0 res=1
[ ? ?3.018142][ ? ?T1] Registered FIQ tty driver
[ ? ?3.030457][ ? ?T1] thermal_sys: Registered thermal governor 'fair_share'
[ ? ?3.030463][ ? ?T1] thermal_sys: Registered thermal governor 'step_wise'
[ ? ?3.037928][ ? ?T1] thermal_sys: Registered thermal governor 'user_space'
[ ? ?3.045288][ ? ?T1] thermal_sys: Registered thermal governor 'power_allocator'
[ ? ?3.053074][ ? ?T1] thermal thermal_zone1: power_allocator: sustainable_power will be estimated
[ ? ?3.070613][ ? ?T1] cpuidle: using governor menu
[ ? ?3.076089][ ? ?T1] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ ? ?3.084446][ ? ?T1] ASID allocator initialised with 65536 entries
[ ? ?3.093598][ ? ?T1] ramoops: dmesg-0?? ?0x20000@0x0000000000110000
[ ? ?3.101516][ ? ?T1] ramoops: console?? ?0x80000@0x0000000000130000
[ ? ?3.108046][ ? ?T1] ramoops: pmsg?? ?0x50000@0x00000000001b0000
[ ? ?3.114743][ ? ?T1] printk: console [ramoops-1] enabled
[ ? ?3.120723][ ? ?T1] pstore: Registered ramoops as persistent store backend
[ ? ?3.128287][ ? ?T1] ramoops: using 0xf0000@0x110000, ecc: 0
[ ? ?3.175956][ ? ?T1] rockchip-gpio fdd60000.gpio0: probed /pinctrl/gpio0@fdd60000
[ ? ?3.184620][ ? ?T1] rockchip-gpio fe740000.gpio1: probed /pinctrl/gpio1@fe740000
[ ? ?3.193238][ ? ?T1] rockchip-gpio fe750000.gpio2: probed /pinctrl/gpio2@fe750000
[ ? ?3.201899][ ? ?T1] rockchip-gpio fe760000.gpio3: probed /pinctrl/gpio3@fe760000
[ ? ?3.210594][ ? ?T1] rockchip-gpio fe770000.gpio4: probed /pinctrl/gpio4@fe770000
[ ? ?3.218839][ ? ?T1] rockchip-pinctrl pinctrl: probed pinctrl
[ ? ?3.246327][ ? ?T1] fiq_debugger fiq_debugger.0: IRQ fiq not found
[ ? ?3.253187][ ? ?T1] fiq_debugger fiq_debugger.0: IRQ wakeup not found
[ ? ?3.260271][ ? ?T1] fiq_debugger_probe: could not install nmi irq handler
[[ ? ?3.267818][ ? ?T1] printk: console [ttyFIQ0] enabled
? ? 3.267818][ ? ?T1] printk: console [ttyFIQ0] enabled
[ ? ?3.278409][ ? ?T1] printk: bootconsole [uart8250] disabled
[ ? ?3.278409][ ? ?T1] printk: bootconsole [uart8250] disabled
[ ? ?3.284737][ ? ?T1] Registered fiq debugger ttyFIQ0
[ ? ?3.285535][ ? ?T1] vcc3v3_sys: supplied by dc_12v
[ ? ?3.285850][ ? ?T1] vcc5v0_sys: supplied by dc_12v
[ ? ?3.286166][ ? ?T1] vcc3v3_lcd0_n: supplied by vcc3v3_sys
[ ? ?3.286470][ ? ?T1] vcc3v3_lcd1_n: supplied by vcc3v3_sys
[ ? ?3.287407][ ? ?T1] iommu: Default domain type: Translated?
[ ? ?3.290735][ ? ?T1] init adp5585_i2c_init
[ ? ?3.291099][ ? ?T1] SCSI subsystem initialized
[ ? ?3.291443][ ? ?T1] usbcore: registered new interface driver usbfs
[ ? ?3.291493][ ? ?T1] usbcore: registered new interface driver hub
[ ? ?3.291764][ ? ?T1] usbcore: registered new device driver usb
[ ? ?3.292224][ ? ?T1] mc: Linux media interface: v0.10
[ ? ?3.292262][ ? ?T1] videodev: Linux video capture interface: v2.00
[ ? ?3.292351][ ? ?T1] pps_core: LinuxPPS API ver. 1 registered
[ ? ?3.292362][ ? ?T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ ? ?3.292383][ ? ?T1] PTP clock support registered
[ ? ?3.293031][ ? ?T1] arm-scmi firmware:scmi: SCMI Notifications - Core Enabled.
[ ? ?3.293097][ ? ?T1] arm-scmi firmware:scmi: SCMI Protocol v2.0 'rockchip:' Firmware version 0x0
[ ? ?3.295184][ ? ?T1] Advanced Linux Sound Architecture Driver Initialized.
[ ? ?3.295646][ ? ?T1] Bluetooth: Core ver 2.22
[ ? ?3.295699][ ? ?T1] NET: Registered protocol family 31
[ ? ?3.295710][ ? ?T1] Bluetooth: HCI device and connection manager initialized
[ ? ?3.295729][ ? ?T1] Bluetooth: HCI socket layer initialized
[ ? ?3.295741][ ? ?T1] Bluetooth: L2CAP socket layer initialized
[ ? ?3.295765][ ? ?T1] Bluetooth: SCO socket layer initialized
[ ? ?3.296015][ ? ?T1] [BT_RFKILL]: Enter rfkill_rk_init
[ ? ?3.296027][ ? ?T1] [WLAN_RFKILL]: Enter rfkill_wlan_init
[ ? ?3.296427][ ? ?T1] [WLAN_RFKILL]: Enter rfkill_wlan_probe
[ ? ?3.296469][ ? ?T1] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = ap6398s
[ ? ?3.296480][ ? ?T1] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control.
[ ? ?3.296489][ ? ?T1] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gpio.
[ ? ?3.296533][ ? ?T1] [WLAN_RFKILL]: wlan_platdata_parse_dt: WIFI,host_wake_irq = 124, flags = 0.
[ ? ?3.296548][ ? ?T1] [WLAN_RFKILL]: wlan_platdata_parse_dt: The ref_wifi_clk not found !
[ ? ?3.296556][ ? ?T1] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio
[ ? ?3.296566][ ? ?T1] [WLAN_RFKILL]: rfkill_set_wifi_bt_power: 1
[ ? ?3.296575][ ? ?T1] [WLAN_RFKILL]: Exit rfkill_wlan_probe
[ ? ?3.297048][ ? ?T1] rockchip-cpuinfo cpuinfo: SoC?? ??? ?: 35663000
[ ? ?3.297062][ ? ?T1] rockchip-cpuinfo cpuinfo: Serial?? ??? ?: 21e81be9ad010d82
[ ? ?3.297936][ ? ?T1] clocksource: Switched to clocksource arch_sys_counter
[ ? ?3.367678][ ? ?T1] VFS: Disk quotas dquot_6.6.0
[ ? ?3.367756][ ? ?T1] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ ? ?3.369560][ ? ?T1] NET: Registered protocol family 2
[ ? ?3.369812][ ? ?T1] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ ? ?3.371455][ ? ?T1] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear)
[ ? ?3.371517][ ? ?T1] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear)
[ ? ?3.371757][ ? ?T1] TCP bind hash table entries: 32768 (order: 7, 524288 bytes, linear)
[ ? ?3.372151][ ? ?T1] TCP: Hash tables configured (established 32768 bind 32768)
[ ? ?3.372282][ ? ?T1] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear)
[ ? ?3.372345][ ? ?T1] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear)
[ ? ?3.372503][ ? ?T1] NET: Registered protocol family 1
[ ? ?3.373338][ ? ?T1] PCI: CLS 0 bytes, default 64
[ ? ?3.373632][ ? ?T1] **** wyb drivers/power/supply/rk817_charger.c rk817_charge_init 1827
[ ? ?3.376131][ ? ?T1] rockchip-thermal fe710000.tsadc: tsadc is probed successfully!
[ ? ?3.377315][ ? ?T1] hw perfevents: enabled with armv8_cortex_a55 PMU driver, 7 counters available
[ ? ?3.379401][ ? ?T1] Initialise system trusted keyrings
[ ? ?3.379661][ ? ?T1] workingset: timestamp_bits=46 max_order=20 bucket_order=0
[ ? ?3.384095][ ? ?T1] utf8_selftest: All 154 tests passed
[ ? ?3.384909][ ? ?T1] Key type cifs.idmap registered
[ ? ?3.384935][ ? ?T1] ntfs: driver 2.1.32 [Flags: R/O].
[ ? ?3.385074][ ? ?T1] fuse: init (API version 7.32)
[ ? ?3.413139][ ? ?T1] Key type asymmetric registered
[ ? ?3.413159][ ? ?T1] Asymmetric key parser 'x509' registered
[ ? ?3.413204][ ? ?T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 242)
[ ? ?3.413217][ ? ?T1] io scheduler mq-deadline registered
[ ? ?3.413226][ ? ?T1] io scheduler kyber registered
[ ? ?3.413335][ ? ?T1] io scheduler bfq registered
[ ? ?3.414102][ ? ?T1] rockchip-csi2-dphy-hw fe870000.csi2-dphy-hw: csi2 dphy hw probe successfully!
[ ? ?3.414933][ ? ?T1] rockchip-csi2-dphy csi2-dphy1: csi2 dphy1 probe successfully!
[ ? ?3.425905][ ? ?T1] pwm-backlight backlight: supply power not found, using dummy regulator
[ ? ?3.426573][ ? ?T1] iep: Module initialized.
[ ? ?3.426646][ ? ?T1] mpp_service mpp-srv: bf01f36bd3 author: lixin 2023-09-23 base on android-13.0-mid-rkr6
[ ? ?3.426659][ ? ?T1] mpp_service mpp-srv: probe start
[ ? ?3.428846][ ? ?T1] mpp_vdpu2 fdea0400.vdpu: Adding to iommu group 1
[ ? ?3.429064][ ? ?T1] mpp_vdpu2 fdea0400.vdpu: probe device
[ ? ?3.429621][ ? ?T1] mpp_vdpu2 fdea0400.vdpu: probing finish
[ ? ?3.430131][ ? ?T1] mpp_vepu2 fdee0000.vepu: Adding to iommu group 3
[ ? ?3.430316][ ? ?T1] mpp_vepu2 fdee0000.vepu: probing start
[ ? ?3.430820][ ? ?T1] mpp_vepu2 fdee0000.vepu: probing finish
[ ? ?3.431479][ ? ?T1] mpp-iep2 fdef0000.iep: Adding to iommu group 4
[ ? ?3.431668][ ? ?T1] mpp-iep2 fdef0000.iep: probe device
[ ? ?3.431962][ ? ?T1] mpp-iep2 fdef0000.iep: allocate roi buffer failed
[ ? ?3.432225][ ? ?T1] mpp-iep2 fdef0000.iep: probing finish
[ ? ?3.432719][ ? ?T1] mpp_jpgdec fded0000.jpegd: Adding to iommu group 2
[ ? ?3.432893][ ? ?T1] mpp_jpgdec fded0000.jpegd: probe device
[ ? ?3.433430][ ? ?T1] mpp_jpgdec fded0000.jpegd: probing finish
[ ? ?3.435025][ ? ?T1] mpp_service mpp-srv: probe success
[ ? ?3.440134][ ? ?T1] dma-pl330 fe530000.dmac: Loaded driver for PL330 DMAC-241330
[ ? ?3.440161][ ? ?T1] dma-pl330 fe530000.dmac: ?? ?DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[ ? ?3.442332][ ? ?T1] dma-pl330 fe550000.dmac: Loaded driver for PL330 DMAC-241330
[ ? ?3.442349][ ? ?T1] dma-pl330 fe550000.dmac: ?? ?DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[ ? ?3.442762][ ? ?T1] rockchip-pvtm fde00000.pvtm: pvtm@0 probed
[ ? ?3.442907][ ? ?T1] rockchip-pvtm fde80000.pvtm: pvtm@1 probed
[ ? ?3.443045][ ? ?T1] rockchip-pvtm fde90000.pvtm: pvtm@2 probed
[ ? ?3.443694][ ? ?T1] rockchip-system-monitor rockchip-system-monitor: system monitor probe
[ ? ?3.444570][ ? ?T1] arm-scmi firmware:scmi: Failed. SCMI protocol 22 not active.
[ ? ?3.445045][ ? ?T1] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled
[ ? ?3.446094][ ? ?T1] fe650000.serial: ttyS1 at MMIO 0xfe650000 (irq = 69, base_baud = 1500000) is a 16550A
[ ? ?3.446918][ ? ?T1] fe670000.serial: ttyS3 at MMIO 0xfe670000 (irq = 70, base_baud = 1500000) is a 16550A
[ ? ?3.447510][ ? ?T1] fe6a0000.serial: ttyS6 at MMIO 0xfe6a0000 (irq = 71, base_baud = 1500000) is a 16550A
[ ? ?3.448072][ ? ?T1] fe6b0000.serial: ttyS7 at MMIO 0xfe6b0000 (irq = 72, base_baud = 1500000) is a 16550A
[ ? ?3.448614][ ? ?T1] fe6d0000.serial: ttyS9 at MMIO 0xfe6d0000 (irq = 73, base_baud = 1500000) is a 16550A
[ ? ?3.450653][ ? T67] random: crng init done
[ ? ?3.451500][ ? ?T1] rockchip-vop2 fe040000.vop: Adding to iommu group 8
[ ? ?3.460144][ ? ?T1] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp0 assign plane mask: 0x0, primary plane phy id: -1
[ ? ?3.460175][ ? ?T1] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp1 assign plane mask: 0x3f, primary plane phy id: 4
[ ? ?3.460188][ ? ?T1] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp2 assign plane mask: 0x0, primary plane phy id: -1
[ ? ?3.460656][ ? ?T1] rockchip-drm display-subsystem: bound fe040000.vop (ops vop2_component_ops)
[ ? ?3.460752][ ? ?T1] dw-mipi-dsi-rockchip fe060000.dsi: failed to find panel or bridge: -517
[ ? ?3.470777][ ? T16] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ ? ?3.478125][ ? ?T1] brd: module loaded
[ ? ?3.489226][ ? ?T1] loop: module loaded
[ ? ?3.489657][ ? ?T1] zram: Added device: zram0
[ ? ?3.490035][ ? ?T1] system_heap: orders[0] = 6
[ ? ?3.490048][ ? ?T1] system_heap: orders[1] = 4
[ ? ?3.490056][ ? ?T1] system_heap: orders[2] = 0
[ ? ?3.491012][ ? ?T1] SCSI Media Changer driver v0.25?
[ ? ?3.492023][ ? ?T1] ahci fc800000.sata: supply ahci not found, using dummy regulator
[ ? ?3.492174][ ? ?T1] ahci fc800000.sata: supply phy not found, using dummy regulator
[ ? ?3.492310][ ? ?T1] ahci fc800000.sata: supply target not found, using dummy regulator
[ ? ?3.492453][ ? ?T1] ahci fc800000.sata: forcing port_map 0x0 -> 0x1
[ ? ?3.492499][ ? ?T1] ahci fc800000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
[ ? ?3.492515][ ? ?T1] ahci fc800000.sata: flags: ncq sntf pm led clo only pmp fbs pio slum part ccc apst?
[ ? ?3.492535][ ? ?T1] ahci fc800000.sata: port 0 is not capable of FBS
[ ? ?3.493582][ ? ?T1] scsi host0: ahci
[ ? ?3.493883][ ? ?T1] ata1: SATA max UDMA/133 mmio [mem 0xfc800000-0xfc800fff] port 0x100 irq 19
[ ? ?3.496577][ ? ?T1] rockchip-spi fe620000.spi: probed, poll=0, rsd=0, cs-inactive=0, ready=0
[ ? ?3.497852][ ? ?T1] rockchip-spi fe640000.spi: probed, poll=0, rsd=0, cs-inactive=0, ready=0
[ ? ?3.498212][ ? ?T1] register spi return v = :0
[ ? ?3.499378][ ? ?T1] tun: Universal TUN/TAP device driver, 1.6
[ ? ?3.499567][ ? ?T1] CAN device driver interface
[ ? ?3.501625][ ? ?T1] rk_gmac-dwmac fe010000.ethernet: IRQ eth_lpi not found
[ ? ?3.501848][ ? ?T1] rk_gmac-dwmac fe010000.ethernet: no regulator found
[ ? ?3.501863][ ? ?T1] rk_gmac-dwmac fe010000.ethernet: clock input or output? (input).
[ ? ?3.501874][ ? ?T1] rk_gmac-dwmac fe010000.ethernet: TX delay(0x27).
[ ? ?3.501884][ ? ?T1] rk_gmac-dwmac fe010000.ethernet: RX delay(0xc).
[ ? ?3.501899][ ? ?T1] rk_gmac-dwmac fe010000.ethernet: integrated PHY? (no).
[ ? ?3.501947][ ? ?T1] rk_gmac-dwmac fe010000.ethernet: clock input from PHY
[ ? ?3.502196][ ? ?T1] rk_gmac-dwmac fe010000.ethernet: init for RGMII
[ ? ?3.502443][ ? ?T1] rk_gmac-dwmac fe010000.ethernet: User ID: 0x30, Synopsys ID: 0x51
[ ? ?3.502459][ ? ?T1] rk_gmac-dwmac fe010000.ethernet: ?? ?DWMAC4/5
[ ? ?3.502472][ ? ?T1] rk_gmac-dwmac fe010000.ethernet: DMA HW capability register supported
[ ? ?3.502481][ ? ?T1] rk_gmac-dwmac fe010000.ethernet: RX Checksum Offload Engine supported
[ ? ?3.502490][ ? ?T1] rk_gmac-dwmac fe010000.ethernet: TX Checksum insertion supported
[ ? ?3.502499][ ? ?T1] rk_gmac-dwmac fe010000.ethernet: Wake-Up On Lan supported
[ ? ?3.502572][ ? ?T1] rk_gmac-dwmac fe010000.ethernet: TSO supported
[ ? ?3.502584][ ? ?T1] rk_gmac-dwmac fe010000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ ? ?3.502595][ ? ?T1] rk_gmac-dwmac fe010000.ethernet: TSO feature enabled
[ ? ?3.502605][ ? ?T1] rk_gmac-dwmac fe010000.ethernet: Using 32 bits DMA width
[ ? ?3.634871][ ? ?T1] mdio_bus stmmac-1: MDIO device at address 0 is missing.
[ ? ?3.636147][ ? ?T1] PPP generic driver version 2.4.2
[ ? ?3.636368][ ? ?T1] PPP BSD Compression module registered
[ ? ?3.636381][ ? ?T1] PPP Deflate Compression module registered
[ ? ?3.636408][ ? ?T1] PPP MPPE Compression module registered
[ ? ?3.636418][ ? ?T1] NET: Registered protocol family 24
[ ? ?3.636451][ ? ?T1] PPTP driver version 0.8.5
[ ? ?3.636765][ ? ?T1] usbcore: registered new interface driver catc
[ ? ?3.636822][ ? ?T1] usbcore: registered new interface driver kaweth
[ ? ?3.636832][ ? ?T1] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
[ ? ?3.636879][ ? ?T1] usbcore: registered new interface driver pegasus
[ ? ?3.636926][ ? ?T1] usbcore: registered new interface driver rtl8150
[ ? ?3.636982][ ? ?T1] usbcore: registered new interface driver r8152
[ ? ?3.636993][ ? ?T1] hso: drivers/net/usb/hso.c: Option Wireless
[ ? ?3.637051][ ? ?T1] usbcore: registered new interface driver hso
[ ? ?3.637096][ ? ?T1] usbcore: registered new interface driver asix
[ ? ?3.637139][ ? ?T1] usbcore: registered new interface driver ax88179_178a
[ ? ?3.637188][ ? ?T1] usbcore: registered new interface driver cdc_ether
[ ? ?3.637233][ ? ?T1] usbcore: registered new interface driver cdc_eem
[ ? ?3.637276][ ? ?T1] usbcore: registered new interface driver dm9601
[ ? ?3.637326][ ? ?T1] usbcore: registered new interface driver smsc75xx
[ ? ?3.637385][ ? ?T1] usbcore: registered new interface driver smsc95xx
[ ? ?3.637429][ ? ?T1] usbcore: registered new interface driver gl620a
[ ? ?3.637477][ ? ?T1] usbcore: registered new interface driver net1080
[ ? ?3.637523][ ? ?T1] usbcore: registered new interface driver plusb
[ ? ?3.637567][ ? ?T1] usbcore: registered new interface driver rndis_host
[ ? ?3.637616][ ? ?T1] usbcore: registered new interface driver cdc_subset
[ ? ?3.637662][ ? ?T1] usbcore: registered new interface driver zaurus
[ ? ?3.637707][ ? ?T1] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
[ ? ?3.637756][ ? ?T1] usbcore: registered new interface driver int51x1
[ ? ?3.637801][ ? ?T1] usbcore: registered new interface driver kalmia
[ ? ?3.637851][ ? ?T1] usbcore: registered new interface driver ipheth
[ ? ?3.637893][ ? ?T1] usbcore: registered new interface driver sierra_net
[ ? ?3.637975][ ? ?T1] usbcore: registered new interface driver cx82310_eth
[ ? ?3.638029][ ? ?T1] usbcore: registered new interface driver cdc_ncm
[ ? ?3.638081][ ? ?T1] usbcore: registered new interface driver qmi_wwan_q
[ ? ?3.638128][ ? ?T1] usbcore: registered new interface driver cdc_mbim
[ ? ?3.650437][ ? ?T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ ? ?3.650461][ ? ?T1] ehci-pci: EHCI PCI platform driver
[ ? ?3.650554][ ? ?T1] ehci-platform: EHCI generic platform driver
[ ? ?3.650986][ ? ?T1] phy phy-fe8b0000.usb2-phy.4: illegal mode
[ ? ?3.653028][ ? ?T1] ehci-platform fd800000.usb: EHCI Host Controller
[ ? ?3.653254][ ? ?T1] ehci-platform fd800000.usb: new USB bus registered, assigned bus number 1
[ ? ?3.653384][ ? ?T1] ehci-platform fd800000.usb: irq 20, io mem 0xfd800000
[ ? ?3.664625][ ? ?T1] ehci-platform fd800000.usb: USB 2.0 started, EHCI 1.00
[ ? ?3.664837][ ? ?T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ ? ?3.664850][ ? ?T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ ? ?3.664860][ ? ?T1] usb usb1: Product: EHCI Host Controller
[ ? ?3.664870][ ? ?T1] usb usb1: Manufacturer: Linux 5.10.157+ ehci_hcd
[ ? ?3.664879][ ? ?T1] usb usb1: SerialNumber: fd800000.usb
[ ? ?3.665364][ ? ?T1] hub 1-0:1.0: USB hub found
[ ? ?3.665410][ ? ?T1] hub 1-0:1.0: 1 port detected
[ ? ?3.668134][ ? ?T1] ehci-platform fd880000.usb: EHCI Host Controller
[ ? ?3.668329][ ? ?T1] ehci-platform fd880000.usb: new USB bus registered, assigned bus number 2
[ ? ?3.668441][ ? ?T1] ehci-platform fd880000.usb: irq 22, io mem 0xfd880000
[ ? ?3.681291][ ? ?T1] ehci-platform fd880000.usb: USB 2.0 started, EHCI 1.00
[ ? ?3.681464][ ? ?T1] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ ? ?3.681478][ ? ?T1] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ ? ?3.681488][ ? ?T1] usb usb2: Product: EHCI Host Controller
[ ? ?3.681497][ ? ?T1] usb usb2: Manufacturer: Linux 5.10.157+ ehci_hcd
[ ? ?3.681506][ ? ?T1] usb usb2: SerialNumber: fd880000.usb
[ ? ?3.681958][ ? ?T1] hub 2-0:1.0: USB hub found
[ ? ?3.682001][ ? ?T1] hub 2-0:1.0: 1 port detected
[ ? ?3.682731][ ? ?T1] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ ? ?3.682761][ ? ?T1] ohci-platform: OHCI generic platform driver
[ ? ?3.683070][ ? ?T1] phy phy-fe8b0000.usb2-phy.4: illegal mode
[ ? ?3.683084][ ? ?T1] ohci-platform fd840000.usb: Generic Platform OHCI controller
[ ? ?3.683264][ ? ?T1] ohci-platform fd840000.usb: new USB bus registered, assigned bus number 3
[ ? ?3.683386][ ? ?T1] ohci-platform fd840000.usb: irq 21, io mem 0xfd840000
[ ? ?3.742124][ ? ?T1] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.10
[ ? ?3.742138][ ? ?T1] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ ? ?3.742149][ ? ?T1] usb usb3: Product: Generic Platform OHCI controller
[ ? ?3.742158][ ? ?T1] usb usb3: Manufacturer: Linux 5.10.157+ ohci_hcd
[ ? ?3.742167][ ? ?T1] usb usb3: SerialNumber: fd840000.usb
[ ? ?3.742623][ ? ?T1] hub 3-0:1.0: USB hub found
[ ? ?3.742667][ ? ?T1] hub 3-0:1.0: 1 port detected
[ ? ?3.743232][ ? ?T1] ohci-platform fd8c0000.usb: Generic Platform OHCI controller
[ ? ?3.743441][ ? ?T1] ohci-platform fd8c0000.usb: new USB bus registered, assigned bus number 4
[ ? ?3.743555][ ? ?T1] ohci-platform fd8c0000.usb: irq 23, io mem 0xfd8c0000
[ ? ?3.802129][ ? ?T1] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.10
[ ? ?3.802143][ ? ?T1] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ ? ?3.802153][ ? ?T1] usb usb4: Product: Generic Platform OHCI controller
[ ? ?3.802163][ ? ?T1] usb usb4: Manufacturer: Linux 5.10.157+ ohci_hcd
[ ? ?3.802171][ ? ?T1] usb usb4: SerialNumber: fd8c0000.usb
[ ? ?3.802612][ ? ?T1] hub 4-0:1.0: USB hub found
[ ? ?3.802654][ ? ?T1] hub 4-0:1.0: 1 port detected
[ ? ?3.804001][ ? ?T1] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ ? ?3.804206][ ? ?T1] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 5
[ ? ?3.804351][ ? ?T1] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000200002010010
[ ? ?3.804410][ ? ?T1] xhci-hcd xhci-hcd.0.auto: irq 86, io mem 0xfd000000
[ ? ?3.804764][ ? ?T1] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ ? ?3.804778][ ? ?T1] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ ? ?3.804788][ ? ?T1] usb usb5: Product: xHCI Host Controller
[ ? ?3.804797][ ? ?T1] usb usb5: Manufacturer: Linux 5.10.157+ xhci-hcd
[ ? ?3.804806][ ? ?T1] usb usb5: SerialNumber: xhci-hcd.0.auto
[ ? ?3.805275][ ? ?T1] hub 5-0:1.0: USB hub found
[ ? ?3.805321][ ? ?T1] hub 5-0:1.0: 1 port detected
[ ? ?3.805653][ ? ?T1] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ ? ?3.805816][ ? ?T1] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 6
[ ? ?3.805838][ ? ?T1] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[ ? ?3.805915][ ? ?T1] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[ ? ?3.806045][ ? ?T1] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.10
[ ? ?3.806058][ ? ?T1] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ ? ?3.806068][ ? ?T1] usb usb6: Product: xHCI Host Controller
[ ? ?3.806077][ ? ?T1] usb usb6: Manufacturer: Linux 5.10.157+ xhci-hcd
[ ? ?3.806086][ ? ?T1] usb usb6: SerialNumber: xhci-hcd.0.auto
[ ? ?3.806526][ ? ?T1] hub 6-0:1.0: USB hub found
[ ? ?3.806578][ ? ?T1] hub 6-0:1.0: 1 port detected
[ ? ?3.807055][ ? ?T1] usbcore: registered new interface driver cdc_acm
[ ? ?3.807067][ ? ?T1] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ ? ?3.807151][ ? ?T1] usbcore: registered new interface driver usblp
[ ? ?3.807219][ ? ?T1] usbcore: registered new interface driver cdc_wdm
[ ? ?3.807511][ ? ?T1] usbcore: registered new interface driver uas
[ ? ?3.807605][ ? ?T1] usbcore: registered new interface driver usb-storage
[ ? ?3.807656][ ? T76] ata1: SATA link down (SStatus 0 SControl 300)
[ ? ?3.807669][ ? ?T1] usbcore: registered new interface driver ums-alauda
[ ? ?3.807725][ ? ?T1] usbcore: registered new interface driver ums-cypress
[ ? ?3.807777][ ? ?T1] usbcore: registered new interface driver ums-datafab
[ ? ?3.807826][ ? ?T1] usbcore: registered new interface driver ums_eneub6250
[ ? ?3.807875][ ? ?T1] usbcore: registered new interface driver ums-freecom
[ ? ?3.807956][ ? ?T1] usbcore: registered new interface driver ums-isd200
[ ? ?3.808009][ ? ?T1] usbcore: registered new interface driver ums-jumpshot
[ ? ?3.808067][ ? ?T1] usbcore: registered new interface driver ums-karma
[ ? ?3.808119][ ? ?T1] usbcore: registered new interface driver ums-onetouch
[ ? ?3.808170][ ? ?T1] usbcore: registered new interface driver ums-sddr09
[ ? ?3.808220][ ? ?T1] usbcore: registered new interface driver ums-sddr55
[ ? ?3.808270][ ? ?T1] usbcore: registered new interface driver ums-usbat
[ ? ?3.808370][ ? ?T1] usbcore: registered new interface driver usbserial_generic
[ ? ?3.808400][ ? ?T1] usbserial: USB Serial support registered for generic
[ ? ?3.808459][ ? ?T1] usbcore: registered new interface driver cp210x
[ ? ?3.808486][ ? ?T1] usbserial: USB Serial support registered for cp210x
[ ? ?3.808553][ ? ?T1] usbcore: registered new interface driver ftdi_sio
[ ? ?3.808581][ ? ?T1] usbserial: USB Serial support registered for FTDI USB Serial Device
[ ? ?3.808698][ ? ?T1] usbcore: registered new interface driver option
[ ? ?3.808727][ ? ?T1] usbserial: USB Serial support registered for GSM modem (1-port)
[ ? ?3.808879][ ? ?T1] usbcore: registered new interface driver trancevibrator
[ ? ?3.809769][ ? ?T1] usbcore: registered new interface driver xpad
[ ? ?3.809839][ ? ?T1] usbcore: registered new interface driver usb_acecad
[ ? ?3.809895][ ? ?T1] usbcore: registered new interface driver aiptek
[ ? ?3.809949][ ? ?T1] usbcore: registered new interface driver gtco
[ ? ?3.810001][ ? ?T1] usbcore: registered new interface driver hanwang
[ ? ?3.810053][ ? ?T1] usbcore: registered new interface driver kbtab
[ ? ?3.810201][ ? ?T1] <<-GTP-INFO->> GTP driver installing...
[ ? ?3.812289][ ? ?T1] i2c /dev entries driver
[ ? ?3.815512][ ? ?T1] rk808 0-0020: chip id: 0x8090
[ ? ?3.815565][ ? ?T1] rk808 0-0020: No cache defaults, reading back from HW
[ ? ?3.839287][ ? ?T1] rk808 0-0020: source: on=0x10, off=0x00
[ ? ?3.839306][ ? ?T1] rk808 0-0020: support dcdc3 fb mode:-22, 0
[ ? ?3.839319][ ? ?T1] rk808 0-0020: support pmic reset mode:0,0
[ ? ?3.845241][ ? ?T1] rk808-regulator rk808-regulator: there is no dvs0 gpio
[ ? ?3.845278][ ? ?T1] rk808-regulator rk808-regulator: there is no dvs1 gpio
[ ? ?3.845714][ ? ?T1] vdd_logic: supplied by vcc3v3_sys
[ ? ?3.846759][ ? ?T1] vdd_gpu: supplied by vcc3v3_sys
[ ? ?3.847390][ ? ?T1] vcc_ddr: supplied by vcc3v3_sys
[ ? ?3.848083][ ? ?T1] vdd_npu: supplied by vcc3v3_sys
[ ? ?3.849071][ ? ?T1] vcc_1v8: supplied by vcc3v3_sys
[ ? ?3.849686][ ? ?T1] vdda0v9_image: supplied by vcc3v3_sys
[ ? ?3.851150][ ? ?T1] vdda_0v9: supplied by vcc3v3_sys
[ ? ?3.852300][ ? ?T1] vdda0v9_pmu: supplied by vcc3v3_sys
[ ? ?3.853437][ ? ?T1] vccio_acodec: supplied by vcc3v3_sys
[ ? ?3.854910][ ? ?T1] vccio_sd: supplied by vcc3v3_sys
[ ? ?3.856045][ ? ?T1] vcc3v3_pmu: supplied by vcc3v3_sys
[ ? ?3.857507][ ? ?T1] vcca_1v8: supplied by vcc3v3_sys
[ ? ?3.858645][ ? ?T1] vcca1v8_pmu: supplied by vcc3v3_sys
[ ? ?3.859781][ ? ?T1] vcca1v8_image: supplied by vcc3v3_sys
[ ? ?3.861278][ ? ?T1] vcc_3v3: supplied by vcc3v3_sys
[ ? ?3.862220][ ? ?T1] vcc3v3_sd: supplied by vcc3v3_sys
[ ? ?3.863861][ ? ?T1] rk817-battery rk817-battery: DMA mask not set
[ ? ?3.864010][ ? ?T1] rk817-battery rk817-battery: fb_temperature missing!
[ ? ?3.864026][ ? ?T1] rk817-battery rk817-battery: zero_reserve_dsoc missing!
[ ? ?3.864040][ ? ?T1] rk817-battery rk817-battery: low_power_sleep missing!
[ ? ?3.864052][ ? ?T1] rk817-battery rk817-battery: battery design_max_voltage missing!
[ ? ?3.864080][ ? ?T1] rk817-battery rk817-battery: full detect gpio: 21, flag: 0
[ ? ?3.864100][ ? ?T1] rk817-battery rk817-battery: plug detect gpio: 23, flag: 1
[ ? ?3.864110][ ? ?T1] rk817-battery rk817-battery: not have to register ?dc_rpdzkj_psy!
[ ? ?3.887579][ ? ?T1] rk817-bat: initialized yet..
[ ? ?3.934055][ ? ?T1] thermal thermal_zone2: power_allocator: sustainable_power will be estimated
[ ? ?3.937736][ ? ?T1] **** wyb drivers/power/supply/rk817_battery.c rk809_charge_init_irqs 3117 charger plug out!
[ ? ?3.937824][ ? ?T1] rk817-charger: Failed to locate of_node [id: -1]
[ ? ?3.938091][ ? ?T1] rk817-charger rk817-charger: Failed to find matching dt id
[ ? ?3.941311][ ? ?T1] input: rk805 pwrkey as /devices/platform/fdd40000.i2c/i2c-0/0-0020/rk805-pwrkey/input/input0
[ ? ?3.944102][ ? ?T1] fan53555-regulator 0-001c: FAN53555 Option[12] Rev[15] Detected!
[ ? ?3.945854][ ? ?T1] vdd_cpu: supplied by vcc5v0_sys
[ ? ?3.951467][ ? ?T7] **** wyb 2024/4/3 19:57 drivers/input/touchscreen/edt-ft5x06.c edt_ft5x06_ts_probe 1158
[ ? ?3.955412][ ? ?T1] rtc-hym8563 4-0051: rtc information is valid
[ ? ?3.960769][ ? ?T1] rtc-hym8563 4-0051: registered as rtc0
[ ? ?3.961816][ ? ?T1] rtc-hym8563 4-0051: setting system clock to 2021-01-01T12:27:14 UTC (1609504034)
[ ? ?3.965544][ ? ?T1] rockchip-mipi-csi2-hw fdfb0000.mipi-csi2-hw: enter mipi csi2 hw probe!
[ ? ?3.965725][ ? ?T1] rockchip-mipi-csi2-hw fdfb0000.mipi-csi2-hw: probe success, v4l2_dev:mipi-csi2-hw!
[ ? ?3.967275][ ? ?T1] rkisp_hw fdff0000.rkisp: Adding to iommu group 7
[ ? ?3.967553][ ? ?T1] rkisp_hw fdff0000.rkisp: is_thunderboot: 0
[ ? ?3.967569][ ? ?T1] rkisp_hw fdff0000.rkisp: max input:0x0@0fps
[ ? ?3.967599][ ? ?T1] rkisp_hw fdff0000.rkisp: can't request region for resource [mem 0xfdff0000-0xfdffffff]
[ ? ?3.967775][ ? ?T1] rkisp_hw fdff0000.rkisp: no find phandle sram
[ ? ?3.968315][ ? ?T1] rkisp rkisp-vir0: rkisp driver version: v02.02.02
[ ? ?3.968478][ ? ?T1] rkisp rkisp-vir0: No memory-region-thunderboot specified
[ ? ?3.968700][ ? ?T1] rkisp rkisp-vir0: Entity type for entity rkisp-isp-subdev was not initialized!
[ ? ?3.968722][ ? ?T1] rkisp rkisp-vir0: Entity type for entity rkisp-csi-subdev was not initialized!
[ ? ?3.971757][ ? ?T1] usbcore: registered new interface driver uvcvideo
[ ? ?3.971773][ ? ?T1] USB Video Class driver (1.1.1)
[ ? ?3.972865][ ? ?T1] test_power_init: test power disabled
[ ? ?3.974402][ ? ?T1] device-mapper: uevent: version 1.0.3
[ ? ?3.974696][ ? ?T1] device-mapper: ioctl: 4.44.0-ioctl (2021-02-01) initialised: dm-devel@redhat.com
[ ? ?3.974970][ ? ?T1] Bluetooth: HCI UART driver ver 2.3
[ ? ?3.974985][ ? ?T1] Bluetooth: HCI UART protocol H4 registered
[ ? ?3.975645][ ? ?T1] cpu cpu0: bin=0
[ ? ?3.975693][ ? ?T1] cpu cpu0: leakage=29
[ ? ?3.975737][ ? ?T1] cpu cpu0: pvtm = 88210, from nvmem
[ ? ?3.975756][ ? ?T1] cpu cpu0: pvtm-volt-sel=2
[ ? ?3.975820][ ? ?T1] cpu cpu0: soc version=0, speed=2
[ ? ?3.977565][ ? ?T1] cpu cpu0: avs=0
[ ? ?3.977892][ ? ?T1] cpu cpu0: EM: created perf domain
[ ? ?3.977988][ ? ?T1] cpu cpu0: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0
[ ? ?3.984016][ ? ?T1] sdhci: Secure Digital Host Controller Interface driver
[ ? ?3.984037][ ? ?T1] sdhci: Copyright(c) Pierre Ossman
[ ? ?3.984046][ ? ?T1] Synopsys Designware Multimedia Card Interface Driver
[ ? ?3.984846][ ? ?T1] sdhci-pltfm: SDHCI platform and OF driver helper
[ ? ?3.985951][ ? ?T9] dwmmc_rockchip fe000000.dwmmc: No normal pinctrl state
[ ? ?3.985978][ ? ?T9] dwmmc_rockchip fe000000.dwmmc: No idle pinctrl state
[ ? ?3.986109][ ? ?T9] dwmmc_rockchip fe000000.dwmmc: IDMAC supports 32-bit address mode.
[ ? ?3.986171][ ? ?T9] dwmmc_rockchip fe000000.dwmmc: Using internal DMA controller.
[ ? ?3.986189][ ? ?T9] dwmmc_rockchip fe000000.dwmmc: Version ID is 270a
[ ? ?3.986247][ ? T91] dwmmc_rockchip fe2b0000.dwmmc: No normal pinctrl state
[ ? ?3.986252][ ? ?T9] dwmmc_rockchip fe000000.dwmmc: DW MMC controller at irq 52,32 bit host data width,256 deep fifo
[ ? ?3.986321][ ? T91] dwmmc_rockchip fe2b0000.dwmmc: No idle pinctrl state
[ ? ?3.986452][ ? T91] dwmmc_rockchip fe2b0000.dwmmc: IDMAC supports 32-bit address mode.
[ ? ?3.986504][ ? T91] dwmmc_rockchip fe2b0000.dwmmc: Using internal DMA controller.
[ ? ?3.986520][ ? T91] dwmmc_rockchip fe2b0000.dwmmc: Version ID is 270a
[ ? ?3.986580][ ? T91] dwmmc_rockchip fe2b0000.dwmmc: DW MMC controller at irq 53,32 bit host data width,256 deep fifo
[ ? ?3.986645][ ? ?T9] dwmmc_rockchip fe000000.dwmmc: allocated mmc-pwrseq
[ ? ?3.986663][ ? ?T9] mmc_host mmc3: card is non-removable.
[ ? ?3.987643][ ? ?T1] arm-scmi firmware:scmi: Failed. SCMI protocol 17 not active.
[ ? ?3.987740][ ? ?T1] SMCCC: SOC_ID: ARCH_FEATURES(ARCH_SOC_ID) returned error: fffffffffffffffd
[ ? ?3.988530][ ? ?T1] cryptodev: driver 1.12 loaded.
[ ? ?3.988588][ ? ?T1] hid: raw HID events driver (C) Jiri Kosina
[ ? ?3.990822][ ? ?T1] usbcore: registered new interface driver usbhid
[ ? ?3.990836][ ? ?T1] usbhid: USB HID core driver
[ ? ?3.991104][ ? ?T1] ashmem: initialized
[ ? ?3.991571][ ? ?T1] rockchip,bus bus-npu: bin=0
[ ? ?3.991585][ ? ?T1] rockchip,bus bus-npu: Failed to get leakage
[ ? ?3.991636][ ? ?T1] rockchip,bus bus-npu: pvtm = 88210, from nvmem
[ ? ?3.991648][ ? ?T1] rockchip,bus bus-npu: pvtm-volt-sel=1
[ ? ?3.991867][ ? ?T1] rockchip,bus bus-npu: avs=0
[ ? ?3.995096][ ? ?T1] optee: probing for conduit method.
[ ? ?3.995132][ ? ?T1] optee: revision 3.13 (b5340fd6)
[ ? ?3.995325][ ? ?T1] optee: dynamic shared memory is enabled
[ ? ?3.995468][ ? ?T1] optee: initialized driver
[ ? ?3.995956][ ? ?T1] rp_power prepare build 8 gpio
[ ? ?3.996077][ ? ?T1] rp_power request pwr_5v_3v3
[ ? ?3.996098][ ? ?T1] success request gpio75 out
[ ? ?3.996113][ ? ?T1] rp_power request led
[ ? ?3.996125][ ? ?T1] success request gpio114 flash
[ ? ?3.996138][ ? ?T1] rp_power request usb_pwr
[ ? ?3.996149][ ? ?T1] success request gpio6 out
[ ? ?3.996163][ ? ?T1] rp_power request usb_rst
[ ? ?3.996173][ ? ?T1] success request gpio8 out
[ ? ?3.996216][ ? ?T1] rp_power request spk_en
[ ? ?3.996228][ ? ?T1] success request gpio148 out
[ ? ?3.996243][ ? ?T1] rp_power request spk_mute
[ ? ?3.996253][ ? ?T1] success request gpio0 out
[ ? ?3.996268][ ? ?T1] rp_power request usb_mode
[ ? ?3.996278][ ? ?T1] success request gpio18 out
[ ? ?3.996291][ ? ?T1] rp_power request Equipment_EN
[ ? ?3.996301][ ? ?T1] success request gpio97 out
[ ? ?3.996424][ ? ?T1] input: gpio_event as /devices/platform/rp_power/input/input1
[ ? ?3.996696][ ? ?T1] input: gpio_event as /devices/platform/rp_power/input/input2
[ ? ?3.996838][ ? ?T1] rpdzkj wake lock
[ ? ?3.997443][ ? ?T1] rp_gpio prepare build 11 gpio
[ ? ?3.997541][ ? ?T1] rp_gpio request gpio1d0
[ ? ?3.997559][ ? ?T1] success request gpio56 out
[ ? ?3.997574][ ? ?T1] rp_gpio request gpio1d1
[ ? ?3.997585][ ? ?T1] success request gpio57 out
[ ? ?3.997598][ ? ?T1] rp_gpio request gpio1d2
[ ? ?3.997608][ ? ?T1] success request gpio58 out
[ ? ?3.997622][ ? ?T1] rp_gpio request gpio1d3
[ ? ?3.997633][ ? ?T1] success request gpio59 out
[ ? ?3.997652][ ? ?T1] rp_gpio request gpio1d4
[ ? ?3.997663][ ? ?T1] success request gpio60 out
[ ? ?3.997679][ ? ?T1] rp_gpio request gpio4a0
[ ? ?3.997691][ ? ?T1] success request gpio128 out
[ ? ?3.997705][ ? ?T1] rp_gpio request gpio4a1
[ ? ?3.997715][ ? ?T1] success request gpio129 out
[ ? ?3.997729][ ? ?T1] rp_gpio request gpio4a2
[ ? ?3.997739][ ? ?T1] success request gpio130 out
[ ? ?3.997753][ ? ?T1] rp_gpio request gpio4a3
[ ? ?3.997763][ ? ?T1] success request gpio131 out
[ ? ?3.997777][ ? ?T1] rp_gpio request gpio1a4
[ ? ?3.997787][ ? ?T1] success request gpio36 out
[ ? ?3.997801][ ? ?T1] rp_gpio request gpio3c1
[ ? ?3.997812][ ? ?T1] success request gpio113 out
[ ? ?3.998384][ ? ?T1] mhi_init Quectel_Linux_PCIE_MHI_Driver_V1.3.1
[ ? ?3.998594][ ? ?T1] sprd_pci_ep_dev_init Quectel_Linux&Android_SPRD_PCIE_Driver_V1.1.8
[ ? ?3.999043][ ? ?T1] sipc: name=sprd,sipc
[ ? ?3.999051][ ? ?T1] sipc: type=1
[ ? ?3.999057][ ? ?T1] sipc: dst =1
[ ? ?3.999062][ ? ?T1] sipc: ep_dev=0
[ ? ?3.999068][ ? ?T1] sipc: smem_type = 0
[ ? ?3.999541][ ? ?T1] sipc: smem_base=0x2c00000, dst_smem_base=0x2c00000, smem_size=0x300000
[ ? ?3.999548][ ? ?T1] sipc: high_offset=0x0n
[ ? ?3.999551][ ? ?T1] smsg_ipc_create: sprd,sipc
[ ? ?3.999966][ ? ?T1] smem_init: pool addr = 0x2c00000, size = 0x300000 added.
[ ? ?3.999978][ ? ?T1] smsg_ipc_smem_init: ring_base = 0x2c00000, ring_size = 0x1000
[ ? ?4.000714][ ? ?T1] spipe_probe!
[ ? ?4.000729][ ? ?T1] spipe: after parse device tree, name=spipe_nr, dst=1, channel=4, ringnr=15, ?rxbuf_size=0x1000, txbuf_size=0x1000
[ ? ?4.000740][ ? ?T1] sbuf_host_init: channel 1-4, offset = 0x0!
[ ? ?4.000911][ ? T91] mmc_host mmc0: Bus speed (slot 0) = 375000Hz (slot req 400000Hz, actual 375000HZ div = 0)
[ ? ?4.001012][ ?T101] smsg_ch_open: channel 1-4 send open msg!
[ ? ?4.002456][ ? ?T1] spipe_probe!
[ ? ?4.002470][ ? ?T1] spipe: after parse device tree, name=sdiag_nr, dst=1, channel=21, ringnr=1, ?rxbuf_size=0x8000, txbuf_size=0x40000
[ ? ?4.002482][ ? ?T1] sbuf_host_init: channel 1-21, offset = 0x0!
[ ? ?4.002718][ ?T102] smsg_ch_open: channel 1-21 send open msg!
[ ? ?4.002812][ ? ?T1] spipe_probe!
[ ? ?4.002821][ ? ?T1] spipe: after parse device tree, name=stty_nr, dst=1, channel=6, ringnr=32, ?rxbuf_size=0x800, txbuf_size=0x800
[ ? ?4.002831][ ? ?T1] sbuf_host_init: channel 1-6, offset = 0x0!
[ ? ?4.003097][ ?T103] smsg_ch_open: channel 1-6 send open msg!
[ ? ?4.005461][ ? ?T1] spipe_probe!
[ ? ?4.005478][ ? ?T1] spipe: after parse device tree, name=snv_nr, dst=1, channel=40, ringnr=1, ?rxbuf_size=0x1000, txbuf_size=0x40400
[ ? ?4.005489][ ? ?T1] sbuf_host_init: channel 1-40, offset = 0x0!
[ ? ?4.005651][ ?T104] smsg_ch_open: channel 1-40 send open msg!
[ ? ?4.006203][ ? ?T1] spool: name=slog_nr, dst=1, channel=5, pre_cfg=0
[ ? ?4.006213][ ? ?T1] spool: tx_num=0, tx_size=0, rx_num=32, rx_size=65536
[ ? ?4.006393][ ?T105] smsg_ch_open: channel 1-5 send open msg!
[ ? ?4.006793][ ? ?T1] usbcore: registered new interface driver snd-usb-audio
[ ? ?4.008725][ ? ?T1] rk817-codec rk817-codec: DMA mask not set
[ ? ?4.013431][ ? ?T1] netem: version 1.3
[ ? ?4.013451][ ? ?T1] u32 classifier
[ ? ?4.013457][ ? ?T1] ? ? input device check on
[ ? ?4.013463][ ? ?T1] ? ? Actions configured
[ ? ?4.014166][ ? ?T1] xt_time: kernel timezone is -0000
[ ? ?4.014258][ ? ?T1] gre: GRE over IPv4 demultiplexor driver
[ ? ?4.014265][ ? ?T1] IPv4 over IPsec tunneling driver
[ ? ?4.014846][ ? ?T1] Initializing XFRM netlink socket
[ ? ?4.014876][ ? ?T1] IPsec XFRM device driver
[ ? ?4.015141][ ? ?T1] NET: Registered protocol family 10
[ ? ?4.015966][ ? ?T1] Segment Routing with IPv6
[ ? ?4.016034][ ? ?T1] mip6: Mobile IPv6
[ ? ?4.016554][ ? ?T1] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ ? ?4.017128][ ? ?T1] NET: Registered protocol family 17
[ ? ?4.017152][ ? ?T1] NET: Registered protocol family 15
[ ? ?4.017199][ ? ?T1] Bridge firewalling registered
[ ? ?4.017235][ ? ?T1] can: controller area network core
[ ? ?4.017252][ ? T92] mmc2: SDHCI controller on fe310000.sdhci [fe310000.sdhci] using ADMA
[ ? ?4.017276][ ? ?T1] NET: Registered protocol family 29
[ ? ?4.017285][ ? ?T1] can: raw protocol
[ ? ?4.017295][ ? ?T1] can: broadcast manager protocol
[ ? ?4.017306][ ? ?T1] can: netlink gateway - max_hops=1
[ ? ?4.017595][ ? ?T1] Bluetooth: RFCOMM TTY layer initialized
[ ? ?4.017621][ ? ?T1] Bluetooth: RFCOMM socket layer initialized
[ ? ?4.017654][ ? ?T1] Bluetooth: RFCOMM ver 1.11
[ ? ?4.017669][ ? ?T1] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ ? ?4.017675][ ? ?T1] Bluetooth: BNEP filters: protocol multicast
[ ? ?4.017685][ ? ?T1] Bluetooth: BNEP socket layer initialized
[ ? ?4.017692][ ? ?T1] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ ? ?4.017700][ ? ?T1] Bluetooth: HIDP socket layer initialized
[ ? ?4.017835][ ? ?T1] l2tp_core: L2TP core driver, V2.0
[ ? ?4.017849][ ? ?T1] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ ? ?4.018734][ ? ?T1] gc2093 2-0037: driver version: 00.01.02
[ ? ?4.018865][ ? ?T1] gc2093 2-0037: Failed to get pwdn-gpios
[ ? ?4.018901][ ? ?T1] gc2093 2-0037: supply dovdd not found, using dummy regulator
[ ? ?4.019009][ ? ?T1] gc2093 2-0037: supply avdd not found, using dummy regulator
[ ? ?4.019055][ ? ?T1] gc2093 2-0037: supply dvdd not found, using dummy regulator
[ ? ?4.041495][ ? ?T1] gc2093 2-0037: i2c read failed at addr: 3f0
[ ? ?4.041690][ ? ?T1] gc2093 2-0037: i2c read failed at addr: 3f1
[ ? ?4.041700][ ? ?T1] gc2093 2-0037: Failed to read sensor id, (-6)
[ ? ?4.042701][ ? ?T1] registered taskstats version 1
[ ? ?4.042723][ ? ?T1] Loading compiled-in X.509 certificates
[ ? ?4.042858][ ? ?T1] Key type .fscrypt registered
[ ? ?4.042867][ ? ?T1] Key type fscrypt-provisioning registered
[ ? ?4.043074][ ? ?T1] pstore: Using crash dump compression: deflate
[ ? ?4.043929][ ? ?T1] rga: rga2, irq = 31, match scheduler
[ ? ?4.044376][ ? ?T1] rga: rga2 hardware loaded successfully, hw_version:3.2.63318.
[ ? ?4.044402][ ? ?T1] rga: rga2 probe successfully
[ ? ?4.044673][ ? ?T1] rga_iommu: IOMMU binding successfully, default mapping core[0x4]
[ ? ?4.044923][ ? ?T1] rga: Module initialized. v1.2.27
[ ? ?4.058728][ ? T36] mmc2: Host Software Queue enabled
[ ? ?4.058765][ ? T36] mmc2: new HS200 MMC card at address 0001
[ ? ?4.059447][ ? T36] mmcblk2: mmc2:0001 SPeMMC 29.0 GiB?
[ ? ?4.059632][ ? T36] mmcblk2boot0: mmc2:0001 SPeMMC partition 1 4.00 MiB
[ ? ?4.059812][ ? T36] mmcblk2boot1: mmc2:0001 SPeMMC partition 2 4.00 MiB
[ ? ?4.060038][ ? T36] mmcblk2rpmb: mmc2:0001 SPeMMC partition 3 4.00 MiB, chardev (235:0)
[ ? ?4.063438][ ? T36] ?mmcblk2: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15
[ ? ?4.127072][ ?T110] vendor storage:20190527 ret = 0
[ ? ?4.204917][ ? ?T9] mmc_host mmc3: Bus speed (slot 0) = 375000Hz (slot req 400000Hz, actual 375000HZ div = 0)
[ ? ?4.218448][ ? T91] mpp_rkvenc fdf40000.rkvenc: Adding to iommu group 5
[ ? ?4.218630][ ? T91] mpp_rkvenc fdf40000.rkvenc: probing start
[ ? ?4.219086][ ? T91] mpp_rkvenc fdf40000.rkvenc: bin=0
[ ? ?4.219101][ ? T91] mpp_rkvenc fdf40000.rkvenc: Failed to get leakage
[ ? ?4.219146][ ? T91] mpp_rkvenc fdf40000.rkvenc: pvtm = 88210, from nvmem
[ ? ?4.219158][ ? T91] mpp_rkvenc fdf40000.rkvenc: pvtm-volt-sel=1
[ ? ?4.219332][ ? T91] mpp_rkvenc fdf40000.rkvenc: avs=0
[ ? ?4.219440][ ? T91] mpp_rkvenc fdf40000.rkvenc: failed to find power_model node
[ ? ?4.219450][ ? T91] mpp_rkvenc fdf40000.rkvenc: failed to initialize power model
[ ? ?4.219457][ ? T91] mpp_rkvenc fdf40000.rkvenc: failed to get dynamic-coefficient
[ ? ?4.220147][ ? T91] mpp_rkvenc fdf40000.rkvenc: probing finish
[ ? ?4.220510][ ? T91] mpp_rkvdec2 fdf80200.rkvdec: Adding to iommu group 6
[ ? ?4.220695][ ? T91] mpp_rkvdec2 fdf80200.rkvdec: rkvdec, probing start
[ ? ?4.220966][ ? T91] mpp_rkvdec2 fdf80200.rkvdec: shared_niu_a is not found!
[ ? ?4.220976][ ? T91] rkvdec2_init:1022: No niu aclk reset resource define
[ ? ?4.220985][ ? T91] mpp_rkvdec2 fdf80200.rkvdec: shared_niu_h is not found!
[ ? ?4.220991][ ? T91] rkvdec2_init:1025: No niu hclk reset resource define
[ ? ?4.221181][ ? T91] mpp_rkvdec2 fdf80200.rkvdec: bin=0
[ ? ?4.221347][ ? T91] mpp_rkvdec2 fdf80200.rkvdec: leakage=56
[ ? ?4.221360][ ? T91] mpp_rkvdec2 fdf80200.rkvdec: leakage-volt-sel=0
[ ? ?4.221394][ ? T91] mpp_rkvdec2 fdf80200.rkvdec: pvtm = 88210, from nvmem
[ ? ?4.221406][ ? T91] mpp_rkvdec2 fdf80200.rkvdec: pvtm-volt-sel=1
[ ? ?4.221585][ ? T91] mpp_rkvdec2 fdf80200.rkvdec: avs=0
[ ? ?4.221696][ ? T91] mpp_rkvdec2 fdf80200.rkvdec: failed to find power_model node
[ ? ?4.221705][ ? T91] mpp_rkvdec2 fdf80200.rkvdec: failed to initialize power model
[ ? ?4.221713][ ? T91] mpp_rkvdec2 fdf80200.rkvdec: failed to get dynamic-coefficient
[ ? ?4.221823][ ? T91] mpp_rkvdec2 fdf80200.rkvdec: sram_start 0x00000000fdcc0000
[ ? ?4.221832][ ? T91] mpp_rkvdec2 fdf80200.rkvdec: rcb_iova 0x0000000010000000
[ ? ?4.221840][ ? T91] mpp_rkvdec2 fdf80200.rkvdec: sram_size 45056
[ ? ?4.221847][ ? T91] mpp_rkvdec2 fdf80200.rkvdec: rcb_size 65536
[ ? ?4.221855][ ? T91] mpp_rkvdec2 fdf80200.rkvdec: min_width 512
[ ? ?4.221905][ ? T91] mpp_rkvdec2 fdf80200.rkvdec: link mode probe finish
[ ? ?4.221969][ ? T91] mpp_rkvdec2 fdf80200.rkvdec: probing finish
[ ? ?4.223083][ ? T91] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: uart_rts_gpios = 142.
[ ? ?4.223110][ ? T91] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,reset_gpio = 133.
[ ? ?4.223123][ ? T91] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_gpio = 134.
[ ? ?4.223135][ ? T91] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_host_irq = 137.
[ ? ?4.223186][ ? T91] [BT_RFKILL]: Request irq for bt wakeup host
[ ? ?4.223200][ ? ?T9] mali fde60000.gpu: Kernel DDK version g18p0-01eac0
[ ? ?4.223271][ ? T91] [BT_RFKILL]: ** disable irq
[ ? ?4.223464][ ? T91] [BT_RFKILL]: bt_default device registered.
[ ? ?4.223640][ ? ?T9] mali fde60000.gpu: bin=0
[ ? ?4.223675][ ? ?T9] mali fde60000.gpu: leakage=8
[ ? ?4.223708][ ? ?T9] mali fde60000.gpu: pvtm = 88210, from nvmem
[ ? ?4.223724][ ? ?T9] mali fde60000.gpu: pvtm-volt-sel=2
[ ? ?4.223738][ ? ?T9] mali fde60000.gpu: soc version=0, spee寄DR V1.18 f366f69a7d typ 23/07/17-15:48:58

本文來自互聯網用戶投稿,該文觀點僅代表作者本人,不代表本站立場。本站僅提供信息存儲空間服務,不擁有所有權,不承擔相關法律責任。
如若轉載,請注明出處:http://www.pswp.cn/news/902273.shtml
繁體地址,請注明出處:http://hk.pswp.cn/news/902273.shtml
英文地址,請注明出處:http://en.pswp.cn/news/902273.shtml

如若內容造成侵權/違法違規/事實不符,請聯系多彩編程網進行投訴反饋email:809451989@qq.com,一經查實,立即刪除!

相關文章

動態監控進程

1.介紹: top和ps命令很相似,它們都是用來顯示正在執行的進程,top和ps最大的不同之處,在于top在執行中可以更新正在執行的進程. 2.基本語法&#xff1a; top [選項] 選項說明 ??僵死進程&#xff1a;內存沒有釋放,但是進程已經停止工作了,需要及時清理 交互操作說明 應用案…

657SJBH西藏藏藥特產銷售管理系統

畢業論文&#xff08;設計&#xff09;文獻綜述 西藏藏藥特產銷售管理系統的設計與實現 近年來&#xff0c;隨著網絡技術特別是Internet技術的普及和發展&#xff0c;電子商務的開發和應用成為一個熱門領域&#xff0c;在線藏藥特產銷售系統就是這其中的一員。 藏藥產業在西藏…

棧和隊列--數據結構初階(2)(C/C++)

文章目錄 前言理論部分棧的模擬實現STL中的棧容器隊列的模擬實現STL中的隊列容器 作業部分 前言 這期的話會給大家講解棧和隊列的模擬實現和在STL中棧和隊列怎么用的一些知識和習題部分(這部分側重于理論知識&#xff0c;習題倒還是不難) 理論部分 棧的模擬實現 typedef int…

RNN的理解

對于RNN的理解 import torch import torch.nn as nn import torch.nn.functional as F# 手動實現一個簡單的RNN class RNN(nn.Module):def __init__(self, input_size, hidden_size, output_size):super(RNN, self).__init__()# 定義權重矩陣和偏置項self.hidden_size hidden…

二叉查找樹和B樹

二叉查找樹&#xff08;Binary Search Tree, BST&#xff09;和 B 樹&#xff08;B-tree&#xff09;都是用于組織和管理數據的數據結構&#xff0c;但它們在結構、應用場景和性能方面有顯著區別。 二叉查找樹&#xff08;Binary Search Tree, BST&#xff09; 特點&#xff1…

一段式端到端自動駕駛:VAD:Vectorized Scene Representation for Efficient Autonomous Driving

論文地址&#xff1a;https://github.com/hustvl/VAD 代碼地址&#xff1a;https://arxiv.org/pdf/2303.12077 1. 摘要 自動駕駛需要對周圍環境進行全面理解&#xff0c;以實現可靠的軌跡規劃。以往的方法依賴于密集的柵格化場景表示&#xff08;如&#xff1a;占據圖、語義…

OpenCV訓練題

一、創建一個 PyQt 應用程序&#xff0c;該應用程序能夠&#xff1a; 使用 OpenCV 加載一張圖像。在 PyQt 的窗口中顯示這張圖像。提供四個按鈕&#xff08;QPushButton&#xff09;&#xff1a; 一個用于將圖像轉換為灰度圖一個用于將圖像恢復為原始彩色圖一個用于將圖像進行…

opencv函數展示4

一、形態學操作函數 1.基本形態學操作 &#xff08;1&#xff09;cv2.getStructuringElement() &#xff08;2&#xff09;cv2.erode() &#xff08;3&#xff09;cv2.dilate() 2.高級形態學操作 &#xff08;1&#xff09;cv2.morphologyEx() 二、直方圖處理函數 1.直方圖…

iPhone 13P 換超容電池,一年實記的“電池循環次數-容量“柱狀圖

繼上一篇 iPhone 13P 更換"移植電芯"和"超容電池"&#x1f50b;體驗&#xff0c;詳細記錄了如何更換這兩種電池&#xff0c;以及各自的優略勢對比。 一晃一年過去&#xff0c;時間真快&#xff0c;這次分享下記錄了使用超容電池的 “循環次數 - 容量(mAh)…

基于 pnpm + Monorepo + Turbo + 無界微前端 + Vite 的企業級前端工程實踐

基于 pnpm Monorepo Turbo 無界微前端 Vite 的企業級前端工程實踐 一、技術演進&#xff1a;為什么引入 Vite&#xff1f; 在微前端與 Monorepo 架構落地后&#xff0c;構建性能成為新的優化重點&#xff1a; Webpack 構建瓶頸&#xff1a;復雜配置導致開發啟動慢&#…

(五)機器學習---決策樹和隨機森林

在分類問題中還有一個常用算法&#xff1a;就是決策樹。本文將會對決策樹和隨機森林進行介紹。 目錄 一.決策樹的基本原理 &#xff08;1&#xff09;決策樹 &#xff08;2&#xff09;決策樹的構建過程 &#xff08;3&#xff09;決策樹特征選擇 &#xff08;4&#xff0…

Vue3使用AntvG6寫拓撲圖,可添加修改刪除節點和邊

npm安裝antv/g6 npm install antv/g6 --save 上代碼 <template><div id"tpt1" ref"container" style"width: 100%;height: 100%;"></div> </template><script setup>import { Renderer as SVGRenderer } from …

Arduino編譯和燒錄STM32——基于J-link SWD模式

一、安裝Stm32 Arduino支持 在arduino中添加stm32的開發板地址&#xff1a;https://github.com/stm32duino/BoardManagerFiles/raw/main/package_stmicroelectronics_index.json 安裝stm32開發板支持 二、安裝STM32CubeProgrammer 從stm32網站中安裝&#xff1a;https://ww…

智慧城市氣象中臺架構:多源天氣API網關聚合方案

在開發與天氣相關的應用時&#xff0c;獲取準確的天氣信息是一個關鍵需求。萬維易源提供的“天氣預報查詢”API為開發者提供了一個高效、便捷的工具&#xff0c;可以通過簡單的接口調用查詢全國范圍內的天氣信息。本文將詳細介紹如何使用該API&#xff0c;以及其核心功能和調用…

Vue 組件化開發

引言 在當今的 Web 開發領域&#xff0c;構建一個功能豐富且用戶體驗良好的博客是許多開發者的目標。Vue.js 作為一款輕量級且高效的 JavaScript 框架&#xff0c;其組件化開發的特性為我們提供了一種優雅的解決方案。通過將博客拆分成多個獨立的組件&#xff0c;我們可以提高代…

Deno 統一 Node 和 npm,既是 JS 運行時,又是包管理器

Deno 是一個現代的、一體化的、零配置的 JavaScript 運行時、工具鏈&#xff0c;專為 JavaScript 和 TypeScript 開發設計。目前已有數十萬開發者在使用 Deno&#xff0c;其代碼倉庫是 GitHub 上 star 數第二高的 Rust 項目。 Stars 數102620Forks 數5553 主要特點 內置安全性…

應用篇02-鏡頭標定(上)

本節主要介紹相機的標定方法&#xff0c;包括其內、外參數的求解&#xff0c;以及如何使用HALCON標定助手實現標定。 計算機視覺——相機標定(Camera Calibration)_攝像機標定-CSDN博客 1. 原理 本節介紹與相機標定相關的理論知識&#xff0c;不一定全&#xff0c;可以參考相…

PG CTE 遞歸 SQL 翻譯為 達夢版本

文章目錄 PG SQLDM SQL總結 PG SQL with recursive result as (select res_id,phy_res_code,res_name from tbl_res where parent_res_id (select res_id from tbl_res where phy_res_code org96000#20211203155858) and res_type_id 1 union all select t1.res_id, t1.p…

C# Where 泛型約束

在C#中&#xff0c;Where關鍵字主要有兩種用途 1、在泛型約束中限制類型參數 2、在LINQ查詢中篩選數據 本文主要介紹where關鍵字在在泛型約束中的使用 泛型定義中的 where 子句指定對用作泛型類型、方法、委托或本地函數中類型參數的參數類型的約束。通過使用 where 關鍵字和…

《MySQL:MySQL表的約束-主鍵/復合主鍵/唯一鍵/外鍵》

表的約束&#xff1a;表中一定要有各種約束&#xff0c;通過約束&#xff0c;讓未來插入數據庫表中的數據是符合預期的。約束本質是通過技術手段&#xff0c;倒逼程序員插入正確的數據。即&#xff0c;站在mysql的視角&#xff0c;凡是插入進來的數據&#xff0c;都是符合數據約…