如何使用wink框架_如何解決Wink Hub的Z-Wave連接問題

如何使用wink框架

Overall, the Wink hub works extremely well…but sometimes the devices you have connected to it can act a little wonky. Here are some things you can do in order to fix any connection issues with all of those Z-Wave sensors and devices connected to the hub.

總體而言，Wink集線器的運行情況非常好……但是有時您連接到它的設備可能會有點不穩定。您可以采取以下措施來解決所有與集線器相連的Z-Wave傳感器和設備的連接問題。

刷新Z-Wave連接圖 (Refresh the Z-Wave Connection Map)

The great thing about Z-Wave is that it uses mesh networking to connect all of your devices and sensors together. In other words, each individual sensor doesn’t just connect straight to the hub, but rather they can connect to one another before connecting to the hub. This not only allows for each device to transmit a better signal, but the wireless range can be much wider than regular?Wi-Fi.

Z-Wave的偉大之處在于它使用網狀網絡將所有設備和傳感器連接在一起。換句話說，每個傳感器不僅可以直接連接到集線器，還可以在連接到集線器之前相互連接。這不僅允許每個設備傳輸更好的信號，而且無線范圍可以比常規Wi-Fi寬得多。

However, when you add on new Z-Wave sensors over time, they sometimes don’t search out for the best possible route to the hub. So it’s possible that some of your devices and sensors aren’t connecting optimally to nearby devices in order to establish the best connection.

但是，隨著時間的推移添加新的Z-Wave傳感器時，有時它們不會搜索出通往集線器的最佳路線。因此，您的某些設備和傳感器可能無法最佳地連接到附近的設備以建立最佳連接。

To fix this, the Wink hub has a setting available in the Wink app that you can use to refresh the Z-Wave connection map. This essentially resets the connection of all the devices and sensors connected to the hub that use Z-Wave and has them reconnect, automatically figuring out the best possible route to take in order to have the strongest signal.

為了解決這個問題，Wink集線器在Wink應用程序中提供了一個可用設置，您可以用來刷新Z-Wave連接圖。這實際上將重置所有連接到使用Z-Wave的集線器的設備和傳感器的連接，并使它們重新連接，從而自動找出最佳路徑，以產生最強的信號。

To do this, open up the Wink app and tap on the menu button in the top-left corner of the screen.

為此，請打開Wink應用程序，然后點擊屏幕左上角的菜單按鈕。

Next, tap on “Hubs”.

接下來，點擊“集線器”。

Tap on the settings gear icon in the top-right corner.

點擊右上角的設置齒輪圖標。

Select your Wink hub.

選擇您的Wink集線器。

Scroll down and tap on “Z-Wave”.

向下滾動并點擊“ Z-Wave”。

Tap on “Z-Wave Network Rediscovery”.

點擊“ Z-Wave網絡重新發現”。

It will take a few seconds for it to do it’s thing, but you’ll soon see a “Success” alert.

要做這件事需要花費幾秒鐘的時間，但是您很快就會看到“成功”警報。

From there, you’re good to go and hopefully your Z-Wave devices and sensors all have better connections now.

從那里開始，您一切順利，并希望您的Z-Wave設備和傳感器現在都具有更好的連接。

使用設備作為信號中繼器 (Use a Device?as a Signal Repeater)

If the above steps still haven’t fixed your connection issues, take a closer look at where all of your Z-Wave sensors and devices are placed. If you discover that one is farther away than the rest, it’s possible that it might not be getting a good signal from the next-closest device.

如果上述步驟仍不能解決您的連接問題，請仔細查看所有Z-Wave傳感器和設備的放置位置。如果您發現一個比其他設備距離更遠，則可能是它無法從最近的設備獲得良好的信號。

A quick fix for this is to place another?device halfway between the sensor on the outskirts and its closest sensor. This new device will act as a signal repeater of sorts, allowing the problem sensor to finally get the connection it needs. This can also be done on other smarthome hubs that use Z-Wave.

一個快速的解決方法是將另一個設備放置在郊區傳感器與其最接近的傳感器之間的中間位置。這款新設備將充當各種信號中繼器，使問題傳感器最終獲得所需的連接。這也可以在使用Z-Wave的其他智能家居集線器上完成。

Keep in mind, though, that battery-powered sensors will not act as repeaters; only plugged-in modules or powered outlets and switches will work.

但是請記住，電池供電的傳感器不會充當中繼器。只有插入的模塊或帶電的插座和開關才能工作。

In any case, you can either put this new device to good use on something around your house, or just place it wherever and have it solely being used as a signal repeater. If that’s the case, it’s always a good idea to get the cheapest Z-Wave device you can find, like this outlet. Or you can get an actual signal repeater for a bit more.

無論如何，您都可以將這種新設備很好地用在房屋周圍的任何地方，也可以將其放置在任何地方，僅用作信號轉發器。如果是這種情況，總是最好的辦法就是找到您能找到的最便宜的Z-Wave設備，例如此插座。或者，您可以獲得更多的實際信號中繼器。

Of course, be sure to perform a network rediscovery again on your Wink hub so that the new device?can be optimally placed in the Z-Wave map.

當然，請確保在Wink集線器上再次執行網絡重新發現，以便可以將新設備最佳地放置在Z-Wave映射中。

遠離金屬 (Stay Away from Metal)

If you have a lot of door and window sensors (a two-part sensor with a magnet) and are constantly experiencing issues with a few of them, it might be because you have them placed near some kind of metal.

如果您有很多門窗傳感器(帶有磁體的兩部分式傳感器)，并且其中的一些不斷出現問題，那可能是因為您將它們放置在某種金屬附近。

A few inches away from metal is fine, but it’s usually when you place door and window sensors right on a metal part that you start experiencing issues. That’s because?the metal on the door or window is interfering with the magnet system that’s used on the sensors.

距離金屬幾英寸遠是很好的選擇，但是通常是將門窗傳感器恰好放在金屬零件上時，您才開始遇到問題。這是因為門或窗戶上的金屬干擾了傳感器上使用的磁鐵系統。

The good news is that there are ways to get around this, and it usually comes down to McGyvering a mount for the sensor in order to keep it a few inches away from the nearest metal.

好消息是，有很多方法可以解決此問題，通常歸結為McGyvering傳感器的安裝座，以使其與最近的金屬保持幾英寸的距離。

更新集線器的固件 (Update the Hub’s Firmware)

As a last resort, you can always update the hub’s firmware if an update is available and hope that it fixes any connection issues, even after you’ve tried all of the above steps.

作為最后的選擇，即使嘗試了上述所有步驟之后，也始終可以更新集線器的固件(如果有可用的更新)，并希望它可以解決所有連接問題。

If you’re vigilant about keeping all of your devices updated in the first place, you likely already have this taken care of, but if not, it’s likely there’s a hub update waiting for you.

如果您首先保持對所有設備的更新保持警惕，則可能已經做好了這項工作，但如果沒有，則很可能正在等待中心更新。

To update the Wink hub, follow the steps further above to access the hub’s settings in the app. Eventually you’ll come across a small banner at the bottom letting you know of a firmware update.

要更新Wink集線器，請按照上面的步驟操作，以在應用程序中訪問集線器的設置。最終，您會在底部看到一個小橫幅，讓您知道固件更新。