1.hal_usart.c 文件
#include <stdio.h>
#include "hal_usart.h"
#include "stm32F10x.h"//**要根據 使用的是哪個串口 對應修改 串口號 eg：USART1**
void USART_PUTC(char ch)
{/* 等待數據寄存器為空 */while((USART1->SR & 0x40) == 0);/* 寫入數據寄存器 */USART1->DR = (uint8_t)ch;
}
//重指向#pragma import(__use_no_semihosting)struct __FILE
{int handle;
};FILE __stdout;void _sys_exit(int x)
{x = x;
}int fputc(int ch, FILE *f)
{if (ch == '\n'){USART_PUTC('\r');}USART_PUTC(ch);return ch;
}static void hal_usart_Config(void);void hal_UsartInit()
{hal_usart_Config();printf("FreeRtos教程學習\n\r");
}static void hal_usart_Config(void)
{ GPIO_InitTypeDef GPIO_InitStructure;USART_InitTypeDef USART_InitStructure;
// NVIC_InitTypeDef NVIC_InitStructure;RCC_APB2PeriphClockCmd( RCC_APB2Periph_GPIOA,ENABLE);RCC_APB2PeriphClockCmd( RCC_APB2Periph_USART1,ENABLE);/****************GPIO Setting *******************************************/
// USART1_TX -> PA9 , GPIO_InitStructure.GPIO_Pin = DEBUF_TX_PIN; GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP; GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;GPIO_Init(DEBUG_TX_PORT, &GPIO_InitStructure);
// USART1_RX -> PA10GPIO_InitStructure.GPIO_Pin = DEBUF_RX_PIN; GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING; GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz; GPIO_Init(DEBUG_RX_PORT, &GPIO_InitStructure);USART_InitStructure.USART_BaudRate = 115200;USART_InitStructure.USART_WordLength = USART_WordLength_8b;USART_InitStructure.USART_StopBits = USART_StopBits_1;USART_InitStructure.USART_Parity = USART_Parity_No;USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;USART_Init(DEBUG_USART_PORT, &USART_InitStructure); // NVIC_InitStructure.NVIC_IRQChannel = USART1_IRQn;// NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority=3 ;//// NVIC_InitStructure.NVIC_IRQChannelSubPriority = 3; //// NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE; //// NVIC_Init(&NVIC_InitStructure); //// USART_ITConfig(USART1, USART_IT_RXNE, ENABLE);//// USART_ITConfig(USART2, USART_IT_RXNE, ENABLE);//// USART_ITConfig(USART3, USART_IT_RXNE, ENABLE);//// USART_ITConfig(UART5, USART_IT_RXNE, ENABLE);//USART_Cmd(USART1, ENABLE); ///
}//
///
void USART1_IRQHandler(void)
{//unsigned char dat;if(USART_GetITStatus(USART1,USART_IT_RXNE) != RESET){ //dat = USART_ReceiveData(USART1);USART_ClearITPendingBit(USART1,USART_IT_RXNE);}
}2. hal_usar.h 文件
說明：要根據不同單片串口引腳的不同，來改變修改對應引腳
#ifndef _HAL_USART_H
#define _HAL_USART_H#define DEBUG_TX_PORT GPIOA //根據使用串口的 RX,TX 引腳的不同來修改頭文件即可
#define DEBUF_TX_PIN GPIO_Pin_9
#define DEBUG_RX_PORT GPIOA
#define DEBUF_RX_PIN GPIO_Pin_10
#define DEBUG_USART_PORT USART1 //根據利用哪個串口來做Debug口 這里就設置為哪個串口void hal_UsartInit(void);#endif3. 后續使用printf函數時，加入對應頭文件，就能顯示想要顯示的內容
#include <stdio.h>
)
