實驗要求：

拓撲圖

配置

sw1:

[sw1]vlan batch 2 to 6[sw1]int Ethernet 0/0/2	
[sw1-Ethernet0/0/2]port link-type access 
[sw1-Ethernet0/0/2]port default vlan 2
[sw1-Ethernet0/0/2]int e 0/0/4
[sw1-Ethernet0/0/4]port link-ty access 
[sw1-Ethernet0/0/4]port default vlan 2[sw1-Ethernet0/0/2]int g 0/0/1
[sw1-GigabitEthernet0/0/1]port link-type trunk 
[sw1-GigabitEthernet0/0/1]port trunk allow-pass vlan all
[sw1-Ethernet0/0/1]int e 0/0/3
[sw1-Ethernet0/0/3]port hybrid untagged vlan 2 to 6
[sw1-Ethernet0/0/3]port hybrid pvid vlan 3
[sw1-Ethernet0/0/3]int e 0/0/5
[sw1-Ethernet0/0/5]port hybrid untagged vlan 2 to 4
[sw1-Ethernet0/0/5]port hybrid pvid vlan 4//  此接口做混雜接口，便于配置PVID和允許列表是否封裝。因為VLAN3、4、5、6都是同一個區域，如果做trunk接口的話，在做DHCP時需要建立多個子接口就過于麻煩（因為一個子接口只能綁定一個VLAN），所以需要控制接口對數據包的封裝。當VLAN3、4、5、6進入次接口時，直接進入物理接口，不需要打標簽（路由器不識別此標簽），開啟DHCP協議。
[sw1]int e 0/0/1
[sw1-Ethernet0/0/1]port hybrid tagged vlan 2
[sw1-Ethernet0/0/1]port hybrid untagged vlan 3 to 6

sw2:

<Huawei>sys
[Huawei]sys sw2[sw2]vlan batch 2 to 6
[sw2]int g 0/0/1
[sw2-GigabitEthernet0/0/1]port lin
[sw2-GigabitEthernet0/0/1]port link-type trunk 
[sw2-GigabitEthernet0/0/1]port trunk allow-pass vlan all[sw2]int e 0/0/1
[sw2-Ethernet0/0/1]port hybrid untagged vlan 2 3 5
[sw2-Ethernet0/0/1]port hybrid pvid vlan 5[sw2-Ethernet0/0/1]int e 0/0/2
[sw2-Ethernet0/0/2]port hybrid untagged vlan 2 3 6
[sw2-Ethernet0/0/2]port hybrid pvid vlan 6

r1:

<Huawei>sys
[Huawei]sys r1
[r1]int g 0/0/0.1
[r1-GigabitEthernet0/0/0.1]dot1q termination vid 2
[r1-GigabitEthernet0/0/0.1]ip add 192.168.1.254 24
[r1-GigabitEthernet0/0/0.1]arp broadcast enable 
[r1]int g 0/0/0
[r1-GigabitEthernet0/0/0]ip add 192.168.2.254 24
[r1-GigabitEthernet0/0/0]dhcp select global [r1]dhcp enable 
[r1]ip pool v2
[r1-ip-pool-v2]network 192.168.1.0 mask 255.255.255.0
[r1-ip-pool-v2]gateway-list  192.168.1.254
[r1-ip-pool-v2]q
[r1]ip pool v3
[r1-ip-pool-v3]network 192.168.2.0 mask 24
[r1-ip-pool-v3]gateway-list 192.168.2.254[r1-GigabitEthernet0/0/0.2]dhcp select global 
[r1-GigabitEthernet0/0/0.1]dhcp select global 

結果截圖展示