激活小區
ACT NRCELL:;
ACT NRDUCELL:;
去激活小區
DEA NRCELL:;
DEA NRDUCELL:;
查詢小區靜態信息
LST NRCELL:;
LST NRDUCELL:;
查詢小區動態信息
DSP NRCELL:;
DSP NRDUCELL:;
修改幀偏置
MOD GNODEBPARAM:FRAMEOFFSET=70728;
修改子幀配比、時隙結構
MOD NRDUCELL:NRDUCELLID=0,DUPLEXMODE=CELL_TDD,FREQUENCYBAND=N41,SLOTASSIGNMENT=8_2_DDDDDDDSUU,SLOTSTRUCTURE=SS54;
修改下行MIMO層數
MOD NRDUCELLPDSCH:NRDUCELLID=1,MAXMIMOLAYERNUM=LAYER_4;
修改上行MIMO層數
MOD NRDUCELLPUSCH:NRDUCELLID=1,MAXMIMOLAYERCNT=LAYER_2;
NR基站打開識別CPE開關
MOD NRDUCELLRSVDOPTPARAM: NrDuCellId=0, ParamId=14, Param1=20, Param2=0;
打開NR基站預調度
MOD NRDUCELLRSVDOPTPARAM: NrDuCellId=0, ParamId=73, Param1=1;
查詢RLC模式如果不是的話需要修改為AM模式
LST NRCELLQCIBEARER: NrCellId=x, Qci=9;
LST NRDUCELLQCIBEARER: NrDuCellId=0, Qci=9;
LST GNBRLCPARAMGROUP: RlcParamGroupId=3;
查詢對應PDCP參數組中的PDCP序列號長度
LST GNBPDCPPARAMGROUP: PdcpParamGroupId=x;
添加RRU鏈環
ADD RRUCHAIN: RCN=3, TT=TRUNK_CHAIN, AT=LOCALPORT, CONNPORTNUM=1, CONNSN1=0, CONNPN1=3;
添加RRU信息
ADD RRU: CN=0, SRN=153, SN=0, TP=TRUNK, RCN=3, PS=0, RT=AIRU, RS=NO, RN="AAU5612", RXNUM=64, TXNUM=64, MNTMODE=NORMAL, RFDCPWROFFALMDETECTSW=OFF, RFTXSIGNDETECTSW=OFF;
添加扇區
ADD SECTOR: SECTORID=153, ANTNUM=0, CREATESECTOREQM=FALSE;
ADD SECTOREQM: SECTOREQMID=153, SECTORID=153, ANTCFGMODE=BEAM, RRUCN=0, RRUSRN=153, RRUSN=0, BEAMSHAPE=SEC_120DEG, BEAMLAYERSPLIT=None, BEAMAZIMUTHOFFSET=None;
增加基站標識
ADD GNODEBFUNCTION: gNodeBFunctionName="5G", ReferencedApplicationId=1, gNBId=100, gNBIdLength=22;
增加運營商
ADD GNBOPERATOR: OperatorId=1, OperatorName="SXYD-5G", Mcc="460", Mnc="35";
增加跟蹤區
ADD GNBTRACKINGAREA: TrackingAreaId=0, Tac=37262;
5G速率提升MML命令
MOD NRDUCELLRSVDOPTPARAM: NrDuCellId=0, ParamId=26, Param1=63;
MOD NRDUCELLRSVDOPTPARAM: NrDuCellId=0, ParamId=27, Param1=1;
MOD NRDUCELLRSVDPARAM: NrDuCellId=0, RsvdSwParam1=RsvdSwParam1_bit15-1;
MOD GNBPDCPPARAMGROUP: PdcpParamGroupId=5, UlDataSplitThreshold=INFINITY;
MOD GNBRLCPARAMGROUP: RlcParamGroupId=5, RlcMode=AM, UeAmStatusRptProhibitTmr=MS5, gNBAmStatusRptProhibitTmr=MS5, gNBRlcReassemblyTimer=MS5, UeRlcReassemblyTimer=MS5;
MOD NRDUCELLPUCCH: NrDuCellId=7, StructureType=LONG_STRUCTURE, Format3RbNum=4, Format1RbNum=RB4;
MOD NRDUCELLRSVDOPTPARAM: NrDuCellId=x, ParamId=75, Param1=1;//PUSCH搶占PUCCH開關
MOD NRDUCELLPUSCH: NrDuCellId=x, UlDmrsType=TYPE1, UlAdditionalDmrsPos=NOT_CONFIG, MaxMimoLayerCnt=LAYER_4;
MOD NRDUCELLALGOSWITCH: NrDuCellId=x, UlInconsecutiveSchSwitch=UL_NON_CON_SCH_SW-1;
MOD NRDUCELLPRACH: NrDuCellId=x, PrachConfigurationIndex=202;//4:1 SlotAssign場景，PRACH周期為10ms
MOD NRDUCELLALGOSWITCH: NrDuCellId=7, Ul256QamSwitch=UL_256QAM_FIXED;//默認是OFF，如果測256QAM的話就配置，否則就配置成OFF"
//4G側配套使用//-端管識別開關
MOD UECOOPERATIONPARA:SPECUSERCOOPERATIONSWITCH=SpecUeIdentifySwitch-1;
4G側配置5G頻點信息
ADD NRNFREQ:LOCALCELLID=1,DLARFCN=646322;
ADD NREXTERNALCELL:MCC="460",MNC="00",GNODEBID=111111,CELLID=1,DLARFCN=646322,ULARFCNCONFIGIND=NOT_CFG,PHYCELLID=1,TAC=123456;
ADD NRSCGFREQCONFIG:PCCDLEARFCN=1300,SCGDLARFCN=646322;
如果不是AM模式需要修改為AM模式
LST QCIPARA: Qci=9;
LST RLCPDCPPARAGROUP: RlcPdcpParaGroupId=5;
)
